4KSRS22QFW01 KitchenAid Refrigerator - Instructions

The part arrived quickly and I put it in the refrigerator. The only part I didn't like was that the former drawer said "Crisper" on it, and the new drawer is blank.

Well I have to say as a HVAC contractor for 32 years this was a very easy repair for me or anyone who is not a HVAC contractor such as myself. I always like to do a little research on any repairs that I have not performed myself and the instructions and video that was available on this web site was awesome. I did this repair in less them 15 minutes removing parts and reassembly of new part. I did let ice bin sit out for about 10 minutes after I removed ice to de thaw and reach room temperature to keep from cracking frozen plastic parts.The new ice auger drum was a very nice perfect fit and was made of a much better quality plastic then the OEM that was replaced. My mother was very pleased as I did this repair for her at her home and she watched me do the repair and she is 74 years old and she commented that she could have done this repair herself after watching me and she also watched video from this web site after I mentioned it to her. I would highly recommend that if anyone needs parts for there freezer or refrigerator to buy from this web site. The price was much lower then anyplace else I could find and it was shipped to my front door in less then 2 days. I would give this company 5 stars and when I need parts for my refrigerator I will sure stop back here and buy the parts again. Thank You PartSelect and keep up the great job. Ken

I watched the video showing how to disassemble unit and it showed that there was a heat element inside the chute door under the foam seal that needed to be removed and placed in side the new chute door. I spent about 10-15 minutes trying to salvage the element but the adhesive used would not release and the part was rendered unusable. I called the help line and was told that their instructions on that kit said the heating element was no longer required. I finished putting the kit in and the unit works fine

I followed the video instruction to a tee. It's exactly as described. However . . . my old plastic cam was so worn out that it had mushroomed within the inside of the door and would not come out without some "coaxing". And of all times to be unable to locate my needle-nose pliers, this was just plain bad timing. The cam was removed in pieces with the aid of a razor knife and a regular pliers. It took some additional time (approx. 1/2 hr.), but eventually it came out. Once this happened, the rest was a breeze. Moral to the story: Replace the cams on these doors every 5 or 6 years, whether it's needed or not. An ounce of prevention is worth 30 pounds of cure and avoided frustration. And for the few dollars spent on the cam, it just doesn't make sense not to.

Ice door would not close thus letting warm air into the freezer compartment. Thinking the spring was broken, I ordered the Ice Door Kit. When it arrived, I dismantled the dispenser and installed the new parts. After installing all the new parts, I found that my problem was the "Y" end of the bracket that holds the spring pin. It was cracked and would not hold the pin. The bracket seemed to be molded into the panel on the outside of the dispenser. To replace the bracket, I would have had to replace the entire outside panel. I decided to repair the bracket and glue the broken piece. I used cyanoacrylate(CA)super glue that I use in model making. Even though that seemed adequate, I decided to drill a small hole through the bracket, perpendicular to the crack, and install a small screw to strengthen the crack. I also applied a little CA to the screw for good measure. It held fast and so far so good!

Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!

The retaining pins, which are part of the control bracket, that hold the micro switch that powers on the ice dispensor had broken, allowing the micro switch to fall away from actuator paddle. I replace the entire control bracket which holds the 2 micro switches, one for ice dispensing and one for water.

I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

Grasped the base of the old part with pliers and turned a quarter turn until metal stays released and part could be pulled out (two online help videos: one says 1/4 turn clockwise, the other, 1/4 turn counter-clockwise, or, 1/4 in right direction, 3/4 in wrong direction). New part slipped in easily and snapped into place with 1/4 turn. Difficulty getting tray to seat fully until I whacked it with my open hand and it then snapped into place. Remains to be seen if it will be difficult now to remove.

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

Did it entirely by myself while my husband was at work

Followed the online video instruction. Super easy

Took off all screws on box.Removed front of drawer,removed back-up to drawer and auger as one unit. Removed C-clamp on end of auger,this released all the parts. The end of the auger shaft unscrews, remove broken piece and reverse process with new part

I found exact instructions on Youtube. Watched the video. Verified that my Control Bracket was in fact broken by partial disassembly. Ordered the part from PartSeclect. Received the part the next day (though I only paid for ground/standard delivery). Installed the part as described in the video using only two screwdrivers and needlenosed pliers within 14 minutes from start to dispensing water again. My water dispensing was interrupted less than 48 hours. Amazing!!! Thank you. It was fun, fun, fun.PaPa43