Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
loud squeeling noise
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Appearances can be deceiving.....while dis-assembly was a piece of cake; the problem turned out to be failed welds on the dryer drum. REMEMBER this before you make a parts decision. Examine the problem.FIRST! (this comeing from a guy who used to Manage an appliance repair shop WAY back in the day....DUH!)Solution?....new dryer; repair cost too high. None the less...at least I have a spare belt !!!
Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.
i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done
The drum belt was making a squealing noise, and it looked frayed.
After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect PS this dryer is 23 years old.
My dad and I followed the video instructions and it was easy! No more ear piercing noise! I did find that once we took the front of the dryer off there was a lot of lint! Never thought to clean the front of the dryer out! The video was a great way to see exactly what you needed to do, just follow what they say and you will have no problems!
I followed the instructions on previous posts. The only problem I had was trying to remount the drum to the bearing unit which sits in the back of the driver. I just couldn't get the three holes lined up for the screws until I finally laid the dryer on its back, and then presto! - it went together in seconds.
This project probably took me longer than most people because I'm always looking things over and a little cautious in my work. I never realized how simple a dryer system is until I had dismantled this one. I spent $38 to fix my dryer rather than buy a new one. $10 of that was for the belt which I changed only because I was in there. Parts from partselect.com arrived 48 hours after ordering, and I used their basic shipping.
Dismantled the dryer to determine that the belt was broken. Called a local supply outlet to request a belt. They said they couldn't find one. Did an online search and found Part Select. Called with the model number and within three days the part was delivered. Replaced the belt and the dryer was working within an hour. Hardest part was getting the dryer out of the laundry room. I would certainly call PartSelect again if I needed a part.
Go with the usual disassembly process (front clips, two Phillips screws, wiring, etc.) The only thing I would add to the process is that when you replace the bearing on the back of the drum, start the three screws into the holes on the disc BEFORE you try to install it throught the back of the drum. You are making your own threads, so run the screws in and out a few times, then place it on the back of the drum and insert the screws. Hope this helps...
Just a lint screen (which I had replaced once before) but the local parts store wanted more than twice what this cost.
Easy, lint trap in front, unscrewed the old base, threw out the old lint screen which was hanging by a thread, and put the new (and - KEY WORD - cheaper) part in. All by Myswlf!