40441 - Instructions

Removed back of washer with screw driver, Removed outer motor cover with a 17 mm socket (1 bolt), Removed motor stater using 10 mm socket (8 bolts). Left motor plugged in and and tipped to the side exposing the sensor. Unplug and snap off sensor. Reassembled in opposite order. Machine works great. Very easy fix, and perfect fit on part.

Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.

The hardest part was removing the dishwasher from under the counter and cleaning up the large amount of water that poured out when I turned the unit on its side.
The actual pump replacement was pretty easy except there were a lot of extra parts that were only needed for other brands or other models.
I might have tightened one of the large clamps too much as there was a very slight leak after I was done. One or two drops of water per cycle, which evaporates quickly and not worth taking apart again.
It was not hard but took longer than predicted.
Much better than buying a new dishwasher or paying the estimated $350 to an appliance repair company.

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

Saved a bundle over the cost of a new dishwasher. by ultimately replacing the entire motor/pump assembly with one ordered from PartSelect.com And a bonus was a much quieter operating dishwasher!!

Here's what I did:

First tried replacing leaking drain valve shaft seal.
Removed entire motor pump assembly. Replaced seal. Still leaked (although less) because drain valve shaft was worn (corroded.)

Next ordered the entire motor/pump replacement assembly. The parts arrived in 2-1/2 days. (Should have replaced entire pump assembly to start with - all of the same labor to replace just the drain valve shaft seal.)

Anyways, instructions were very clear and well illustrated. This replacement took less time than to do the drain valve shaft seal.

Very simple repair:
1) Shut off water supply, electric power
2) remove front bottom insulated dishwasher cabinet cover grills.
3) disconnect drain hose and catch water in shallow dish.
4) disconnect water supply at solenoid valve.
5)disconnect electrical inside junction box and remove cable from dishwasher.
6) remove two under counter screws to top of tub
7) slide dishwasher out from under cabinets.
8) place soft carpet to cushion left side of dishwasher to avoid potential damage to water inlet to tub..
9) lay dishwasher onto left side. (Not right side, as jet dry reservoir wiill drain empty all over floor.)
10) unfasten motor support rod, power connector, and drain solenoid power connector.
11) unfasten motor ground wire.
undo pump inlet and outlet boot clamps.
12) remove old motor/pump assembly.
13) prepare new motor/pump assembly drain hose adapter stub reducer diameter to pump drain outlet. (tighten two hose clamps provided/)
14) place new motor/pump assembly into inlet and outlet boots.
15) fasten inlet and outlet boot clamps firmly tight.
16) install new, longer motor support rod (front)
17) install motor ground wire and new, fine thread grounding screw,
18) connect motor power to new power pigtail and plug new pigtail into motor power connection,
19) install wire wrap tie threaded through the support rod to front frame hole and support motor power wires/
20) install wire wrap tie through drain valve solenoid metal support holes and loop around solenoid power wires to support them.
21) tilt dishwasher upright and slide back under counter cabinets. Guid power and water supply lines to right under side of pump motor, and drain hose to left side.
22) reattach drain hose to new motor/pump drain stub reduce adapter, tighten hose clamp.
23) support drain hose with wire wrap tie looped over frame on left side.
24) reattach water supply to inlet water solenoid valve and tighten firmly.
25) redo electrical power supply connections to dishwasher hot, neutral, and ground (120VAC).
26) check level of dishwasher tub and adjust front and rear leveling legs on left and right sides. BE SURE LEVEL, OR WATER MAY SPILL OUT TUB WATER INLET OPENING DURING OPERATION.
27) remove inside tub drain trap screen (two screws) , and pull out sump baffle. Check for and remove clear any foreign objects inside tjhe sump.
28) replace sump baffle (flat baffel towards fromt. and tub drain screen cover.
29) Turn on water supply and electirc power supply.
30) Test wash a load of dishes and check for leakage.
31) reinstall fromt lower insulated cover grills.

Wow, the new motor/pump assembly operates very quietly compared to the old one - this is a pleasant and unexpected bonus.

No problems encountered.

Total time was about 2.5 hours to do all of above.

The repair only required me to lift out the old unit and set the new rack into the dishwasher. I was pleased that there was nothing to put together. The rollers were already attached.
It took longer to open the shipping box than to do the installation.

A no brainer. Simply open dishwasher door, remove lower rack and set new rack in place. Roll the new lower rack in dishwasher and close door. It fit perfectly and life routine was instantly on it's way without disruption.

There are two pumps in this system. I turned the washer on its side and took off bottom plate. There are several screws holding this on. I then took the entire pump assembly off. There are 3 screws holding each pump on the brown plastic body. Each pump has a positive and negative lead. I switched out the pump and reassembled. The hardest part is getting the 3 "shock absorbers in place with the rubber sleeves. I think the book suggest getting to the pump from the front side but I went through the bottom. Worked good. I did wonder however if the other pump was working. Do you need two pump working to get flow? By replacing one pump I went from no flow to good flow. Cost me $75.00

I called the repair guy, and he told me I'd have to replace the motor/pump assembly. He said he could do it for around $250 to $300. I logged onto this website for a look and saw the seal available. After reading the other responses, I figured with a seal and the cheap push-nut (that sometimes gets mangled upon removal), it would be worth a try.
I pulled the dishwasher partly out from under the cabinet; disconnected the front support mount, the drain hose, and the two water boots; dropped the motor/pump assembly; removed the solenoid; removed the e-clip, push-nut, shaft, and old seal; and then reinstalled everything. The hardest part of the repair was the tight working conditions. I wonder how many people pay hundreds of dollars because of this $15 part.

I removed a front access panel below the door and found a broken steel cable going to the spring assembly which helps lift the door. I ordered a replacement from PartSelect which arrived quickly. To fix the problem, all I had to do was attach one end of the cable to the springs, route the cable across a nylon wheel, and slip the eyelet end of the cable onto a mounting post. Then reattach the access panel and I was done. Problem fixed.

Rather than remove the dishwasher from the counter, I performed the repair inplace, which was much less work (although I did have to lay on the floor).
After turning off the power, I removed the two access panels at the bottom of the unit, disconnected the wiring from the pump and solenoid, loosened the drain hose fitting and drained most of the water out of the unit and into a shallow pan (the drain solenoid was stuck open, so this was pretty easy - otherwise, I still could have manually actuated the drain valve & solenoid to drain water through this hose).
There was alot of water in the unit and my pan overflowed a little. If I was doing this again, think I would have disconnected the drain hose from under the sink and drained out through that into a bucket (I could have controlled that flow better).
Once the water was out, there are just two hose clamps that hold the pump onto the unit (one on top and one in the back), and a stabilizer bar that connects the motor to the front frame. Removed these and the whole unit came right out.
The replacement pump & motor was exactly the same as the one that came out, so I didn't need any of the hose or wire adapters that came in the kit.
Reconnected the two pump connections, motor bracket and wiring, and the unit was good-to-go!

I did repaired while looking at video at your site .thanks to your team ..

I first thought there was a mechanical problem but after checking everything mechanical I discounted that idea ... I researched and found out from others with a similar problem that the Le code display was probably a sensor problem ... I ordered a replacement sensor ... With the new sensor available, I removed the access panel to the back of the machine (phillips head screw driver - 4 screws) ... Remove the exposed motor half (1 bolt - 17mm scocket) ... Loosen the motor stator that has the wired coils (10mm socket - 6 bolts) ... Hold motor unit to the side without disconnecting the wiring harness ... Disconnect the sensor wire connector and remove the old sensor ... Clip the new sensor in place (same position as the old one) and re-connect ... Reverse the assembly procedures ... This fixed the problem and the washing machine works like a new one ... The wife is HAPPY!

I took the inner door panel off as described by others on this website, cleaned out all the gunk left by 27 yrs of use, and replaced the door gasket and tub baffles. A Phillips-head screwdriver was required to remove the door panel, but no tools were required to replace any of the parts I ordered. I didn't find it necessary to soak the door gasket in warm water as it was pretty flexible right out of the package. I recommend stretching the gasket slightly while pressing it into the groove, particularly around corners, or it will end up being too short at the end. The rinse aid tank had also been leaking Jet-Dry for a long time, so I cleaned that mess up as well and tried to replace the tank. Unfortunately, the new tank did not fit my model of dishwasher even though this website and GE's stated that it did. The shaft on the tank that pokes through the inner door panel to the inside of the dishwasher was too short because >2 mm of it was taken up by a thick rubber washer and a hard plastic collar (fused to the shaft to hold the washer in place) that had not been part of my original rinse aid tank. PartSelect was very good about refunding me for the incorrectly identified rinse aid tank and stated that they would contact GE about correcting this error on their website as well. I therefore cleaned up my original rinse aid tank, rinsing out all Jet-Dry residue inside it, and put it back into the inner door panel. I researched this part and found that GE has redesigned it twice since my dishwasher was manufactured in 1985 -- my original part is no longer available anywhere. So, I will just not use Jet-Dry and will maybe upgrade to a dishwasher powder that includes rinse agent (e.g., Cascade Complete). Replacing the gasket and tub baffles and cleaning up my original rinse aid tank stopped the leak for less than the cost of a repairman's service call and diagnosis fees -- it would have cost me 3X more if he had provided the parts and done the repairs! Replacing my dishwasher was out of the question as they do not make them like they used to (i.e., no microchips or motherboards to fail in a few years) -- this is the first problem I've had with my dishwasher in 27 years! As a side note, I also learned from my research that my front door panel insert is reversible. I was able to remove a side trim piece, slide out the panel, and turn it over so the color is now white rather than the outdated almond. It's like I have a brand new dishwasher that is ready to go for another 27 years.

Wife wanted to spend $800 on a new washer." You don't know what your doing" she said. Parts Select not only showed me how to take it apart, but easy instructions to put back together and a "how bout them apples" to the wife!!!