3ZAED4475TQ0 Admiral Dryer - Instructions

I watched the video on replacing the belt and it was amazingly as easy as the video described. I had asked my son if he could replace it if I couldn't and I didn't have to ask him. If you are only moderately ept at repairing anything you could do this. I was waiting on it when it finally arrived and in no time I had it replaced and my dryer back working. Being a woman I like it when I can repair something myself and not have to rely on someone else to do it.

The repair was pretty simple.
1. unplug dryer.
2. use a med. flat screw driver with some cloth wrapped around the blade as not to chip the paint surface. From the front of the dryer,
carefully pry open the top surface of the dryer. There are 2 points to lift, about 3" from the right side and 3" from the left side.
3. The top will open like the the hood of a car, lift gently, you might have to move the dryer out if you can (if you are on a flexible service connection).
4. Unclip the push bottom elec. switch.
5. Carefully remove 2 sheet metal screws on the top left and top right (from the inside of the dryer cabinet. These hold the front of the dryer in place. You have to remove the front of the dryer to get the drum out. I can't believe that these 2 flimsy screws hold the dryer together.
6. Pull the front panel off, tipping it forward. More on this later, it's really important!!
7. Remove the drum, it's light weight, but bulky.
8. Now you will see the motor assembly and idle pulley.
9. Follow the belt diagram with the replacement belt package.
10. It gets a little tricky to get the drum back in because there's a bit of spring tension on the drum from the belt.
11. You're ready to re assemble. BUT, the next step is really important.
12. Since you have the front panel off, you can get at the lint trap. Yeah, lint. Ever wonder why your favorite Tee shirt gets thinner and thinner? Well, look in the lint trap. I filled a vacum cleaner bag with the hard packed lint.
13. By the way, you have to remove the 2 torx screws that hold the lint trap assembly.
14. Vacuum the whole exhaust pipe while u are at it.
That's it!

I replaced it

The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.

With no experience repairing appliances, I did figure it out that the drive belt was broken since the motor was running and the drum did not turn.

What to do? Start looking for fasteners! I knew I had to get to the drum, but there was nothing up front, on top, or bottom that gave a clue. Only the back panel had hex head steel screws. I removed them and the panel. Then I removed a tube that pulled air from the drum to the outlet. I saw some screws holding the back of the dryer top. After removing them, the top popped off by pulling it up and releasing the attachment at the front.

This gave me access to a couple of screws holding the top of the front (holding the door). It seemed to make sense to lay what was left of the dryer on it's back. After removing the last two screws at the top corners of the front panel, I pulled it up and removed it. The drum lifted right out. The belt tightener was loose and lying against the back wall.

The local Sears did not have a replacement belt and their web site was not that helpful or forgiving. A Google search revealed a site called PartSelect. It had a very useful search routine which led me to make a purchase on a Saturday evening. The belt arrived at my door on the following Tuesday! Be sure to look at the instructions that come with the belt, it will demonstrate how to fish it through the loose belt tightener.

In about 1.5 hours the dryer was back together and doing it's thing. There were two additional screws left over, but I figure that's a manufacturing defect.

I was a hero to the wife, as usual.

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

I pried the top of the dryer with a screw driver and then lifted the top of the dryer, I then removed the two screws "with a nutdriver" that held the door in place and then removed the door and drum. I then got the new belt and placed the belt over the drum and positioned the belt through the idler arm and then on the motor pulley. I had to hold the door and drum to lock the bottom of the dryer door to the dryer and then made sure the rear drum seal was in place and the belt did not slip off the motor pulley

received part 4 days after order. very pleased about that! Local Sears Service center was out of stock.

carefully removed old "handleless" lint filter.
inserted new lint filter and Voila! success.

First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.

Opening the dryer to discover the problem was easy. We put the belt up on a workmate bench - I think this made access better at the bottom. Getting the new belt on past the rear drum seal was ok, the instructions could benefit by including wording describing how to roll the belt flat under the 2 rear drum support pulleys to bring it to the drive motor shaft pulley. The instructions included with the belt had a diagram showing the position of the belt take up idler (the idler was found loose inside the bottom of the dryer), our dryer had a hole in the metal spring clip of the idler arm, so we thought at first that a screw to the chassis had broken - this is not the case the idler pulley is held in place by belt tension, so pulling the spring clip open while feeding the belt would have been useful in the instructions too. Other than those 2 head scratchers the repair was easy and saved us the cost of calling a repairman. Thanks PartSelect.

My 12 year old son and I took off the front of the dryer to see if we could see what was wrong. The belt was snapped and on the floor of the dryer. I ordered the belt from you--it came three days later. That evening, my son held the drum while I laced the belt through the pulley. We cleaned everything up--lots of lint! Put everything back together, plugged it in, turned it on--SUCCESS! We were wildly excited. I am a stay-at-home mom determined to save money any way I can.

Ordered belt, received it two days later. It was a perfect fit.
The top of my dryer pops up from the front where 2 screws will allow the front to drop to the ground. Lift the drum slightly to get the belt on. Had to wrestle with the idler arm for about five minutes, but I won.

First you disconnect electricty then gently pry up the top of dryer with a flat screwdriver. You will find a three wire plug unplug wire and take the two phillip screws our of the switch lift our the switch and reverse the prossess to reinstall new switch

I followed the posted directions from others, and it was a breeze. They were really helpful. I would just add the step of keeping the drum in place with a block of wood underneath before removing the front. Slip the belt around the drum, reattach the front , and then finish positioning and tensioning the belt once the block is out of the way .

We took off the front of the dryer and saw how the new belt needed to go on. It took myself, my daughter, and my husband to get the belt in place and the drum aligned. Once that was done, I put the front of the dryer back on, this holds the drum in place. After that, we sealed the back of the drum like the instructions stated, turned it on, and it worked. We were a little concerned with the instructions stating if the drum was not sealed properly it could cause "fire & death". We kept checking the dryer throughout the evening... no fire, so we were very happy to have done this repair ourselves. Thanks. I would not have tryed it myself except for the positive comments on your site when I looked to order the part. They were correct, it was easy to do and saved us a lot of money in repair service. It also showed my 23 year old daughter how easy it is to some things yourself. :)