3SWED4800YQ2 Whirlpool Dryer - Instructions

I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together to save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!

1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!

I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F

Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.

I removed the top panel, then the front panel.
Removed the belt and the drum.
Saw what I needed to replace. Ordered the parts then put back together. It was a really easy job.

10 min. job, easy to do / two screws top and two inside front / remove old parts install new.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply. New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.

Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!

It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.