3RLGR5437KQ3 Whirlpool Dryer - Instructions

Dryer would not start when the start switch was pushed. I was advised by the local repair shop to replace the "push to start switch" and the "thermal fuze". I unplugged the dryer and removed the back dryer casing which took all of 3 minutes. I removed the start switch and thermal fuze using directions on the whirlpool parts forum. This took maybe 5 minutes. I replaced with the new parts and put the casing back on the dryer. The entire project took 15 minutes. The dryer works perfectly. 34 USD for parts and shipping instead of 600 for a new dryer. Easy to identify the parts needed using the model number and the parts arrived the next morning I will use this company again for sure!

By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.

i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.

removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!

Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done

Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above steps in reverse order and your done.

Old door catch came out, new one slipped in. All works great.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.

I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful

My dryer timer would run through the heat cycle and move in to the cool down cycle. It would not move past the cool down cycle, and would not shut off automatically. I tried replacing the Thermal Fuse first, since I'd already removed the back panel to diagnose the problem. There was no change - the dryer did not shut off automatically. Next, I removed the back cover to the timer console. The Timer Power Resistor looks like a black circle and a rectangle joined together. It was attached to the back of the on/off switch by a single hex head screw, and the resistor has orange and black wires attached. The replacement Power Resistor doesn't look like the resistor that was in my dryer. It is rectangular in shape with 2 male spade connectors. I attached the orange and the black wires to the new power resistor. I started the dryer and it went through a full heat/cool down cycle, and automatically shut off with the end of cycle buzzer sounding. Total part replacement time was about 10 minutes.

Safety First - I unplugged the power source. I removed the console by simply removing several screws. However because the nut fastening the resistor was in a really tight spot and I had little room to work, I decided to remove several screws from the back of the console to open it up. (This step is not necessary - but for me, it just made the job go quicker). I was then able to use my ratchet/socket set to remove the nut from the resistor. I then attached the wires from the timer to the new in-line resistor. I closed up the console, re-attached it to the dryer and DONE!!! The dryer works fine!!! By the way, the set is 25 years old. I initially thought it was the timer itself but after explaining the problem to Rebecca at this iste , she quickly identified the problem as the timer power resistor. Many thanks Rebecca??

removed front of dryer located igniter removed two screws disconnected wires then put new one in also replace thermal fuse and thermostat on back of dryer works great.

I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.

I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (it should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.