3RLGR5437KQ3 Whirlpool Dryer - Instructions

little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install

Unlike your video, with this model, the thermal fuse is located near the front of the dryer, which I didn't find out until the back was already off.

I watched the online video first, which made the removal and installation fast and easy.

went online to whirlpool typed in my problem and. was directed me to Partselect which said it was thermal fuse and had picture where it was located and how to replace,easy as that.thank you PartSelect.Tim

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

First I watched Partselect's wonderful videos on what could cause the dryer from having to use multiple cycles to dry and the parts involved. I then took the back of the dryer off and tested all three parts with a multi-meter to determine which part had no resistance. The thermal fuse did not register any thing, so I ordered the part and a few days later put it in. The dryer dries in just one cycle saving on the cost of repair and electric bill. Partselect.com is my first go to sight for any repair. They make it so simple and comprehensive that any one can do the repair. I then used duct tape to make a secure connection to the duct pipe in order for it to properly vent to the outside.

Previously I had repaired two washing machines and now a dryer, which is why my mom nick named me Josephine. So ladies you can make the repairs as well.

Remove the exhaust tubing connection and the back panel (five nut screws). Locate the fuse; it is just to the right of the lint trap shoot, midway between the top and bottom of the back panel area. Replacement is visually intuitive.

I ordered the part, watched the video and made the repair in less than thirty minutes. This was much cheaper than purchasing a new dryer.

Changed out the thermal fuse because it was easy. Changed the Igniter after that failed to fix the problem. Unfortunately after the igniter it still worked part of the time. I realized that I sometimes wasn't hearing the solenoid click after seeing the igniter glow. Changed the solenoids and we're back in business now.

Pull off the front panel of the dryer, and replaced the thermal fuse. Very easy. Plus, vacuumed out the whole inside of the dryer, the rear and the tube running from the dryer to the outside. Will be doing this at least every 3 months to be safe. You would be surprised at how much lint builds up inside the machine. Eve though we clean the filter trap after every use of a load of clothes.

Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.