3LCGD9100WQ2 Whirlpool Dryer - Instructions

When the part came in my husband was not home and I figured I could put this part on myself. I took the part downstairs, used the nut driver to remove one screw, took the two wires off the old therma fuse, put the wires on the new therma fuse, and screwed the new therma fuse onto the back of the dryer. It really couldn't have been any easier.

Initially thought it was the thermal fuse since that has already been replaced twice before for the same type of problem. After replacing the fuse the same issue remained, so I did a little hunting on the internet and found some matrixes to help diagnose the issue. After a couple of minutes, I discovered it was the ignitor. I immediately ordered the part and received it in about 5 business days. Even though that took longer than previous orders (usually < 3 days), I was still happy to get the part at a MUCH cheaper price than available locally. Installation took about 5 minutes with only a 5/16" nut driver and we were back in business. Kind of glad it broke because the dryer needed a good de-linting and cleaning anyway. : )

took of the back , took out the drying coil ,put the other in , but back on . now it works saved alot of money. love it. Thank you parts select.

This has happened several times to my KitchenAid dryer. It cost more than $100 to bring someone in to repair. Fortunately, I saved my bills and saw the part "thermal fuse" listed. I researched that and found your website. I couldn't believe how easy it was to fix. The part cost less than $15 and the diagrams you provided were a big help. I was about to purchase a new dryer, easily $500. Your site saved me a bunch of money. How I fixed? Unscrewed the back panel of the dryer. Found a part that resembled the part you sent me. Slipped it out. Put the new one in...that is it. I also figured that one reason the part keeps burning out is because my duct has to bend to get to the outside vent. The obstruction probably causes the dryer to overheat more often than not. I pulled the dryer 6 inches more away from the wall to see if that helps. My fuse was going out about every 2 years.

Was working fine one load and not the next. I remembered we had used this site for our dishwasher so gave it a try. Went with most common problem first. Ordered Sun rec'd Tues. Took longer to vacuum the back of dryer then it did to replace the fuse. Cost less than 30 bucks including shipping. Video was cool too.

i still cant get it to start i keep having that 06 code revision after i ran the diagnostic i replace the thermistor right after that the dryer start but only dry one load and wont start again then i replace the thermal fuse still not working i order the door switch hopefully that might do it

Previous consumer help advised to check the Thermal Fuse. A quick check using an ohm meter or simply connecting the leads together, confirmed that the Fuse was open and bad. The other essential item is to clean & vacuum all lint from all other dryer parts on the top, drum & back of the dryer. Be sure to also perform a check of the Cycling Thermostat, located near the Thermo Fuse. This is not a difficult repair. Just be sure to disconnect the 220 V and the circuit breaker. A $9 fuse was better than the cost of a repairman or new dryer. Barry Burke, Cincinnati, Ohio.

I put my mind into the repair based on what I saw for a problem and what was given for advise. I was steered toward the thermal fuse, ordered and installed it. Not repaired, in checking the power backward to the panel I found that the dedicated panel had one side blown still allowing for the motor to run but not the element. hmmm

I found some help on-line that suggested some of the most likely causes. The on-line videos showed how to remove clips/panels to access the parts. Once I found the possibly failed parts, door switch and thermal fuse, I did a quick continuity check and found that the thermal fuse had an open circuit.

Took off the backplate of dryer, replaced fuse, done.

The repair was easy--thanks to your excellent videos--also, delivery was prompt and correct--your service is excellent--but, looks like I'll need another part--maybe door latch??? I'll troubleshoot and definitely contact PartSelect--Thank you--will recommend you!

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

I removed the back panel of the dryer and the thermal fuse was about three quarters down the dryer. The exploded parts schematic was very helpful. I simply removed two screws to replace the thermal fuse and reinstalled the back panel. The dryer works great now.

Using the video on the site I was able to open the back on the dryer, replaced the thermal fuse and close it up in less than 15 minutes. Works great and saved me a ton of money.

I simply unplugged the dryer and removed the backing. Once off I located the part which was in plain sight, unhooked the wires and attached them to the new part. Put backing back on plugged it in and turned it on and it worked.