planetary gear would not turn; discovered worm gear was broken upon dis-assembly of mixer
Followed step-by-step video instructions for dis-assembly/reassembly found at ereplacementparts.com. All went well except when driving out the pin that holds the worm gear in the tower. The video wasn't exactly clear enough about what position the pin should be in when driving it out and I inadvertently drove the pin out so that it was trapped inside the tower assembly. Result? I had to bend the pin to get it out, causing an extra expenditure and wait time to order a new pin. So, lesson learned: be sure the pin is horizontal to the tower and not perpendicular to when driving the pin out. Also, I found that having the mixer apart was a good time to replace the grease in the housing. I don't think it would be required to replace the grease at this time but I was worried that pieces of the old worm gear could remain in the grease and possible get jammed in the gears after repairs were completed. Be sure to get a "food grade" grease not grease from your local auto parts store! The table knife was the best tool to use to remove the grease and to smear the grease all over the internal gears when replacing it.
When using the bread hook, the force of the dough would knock the bowl out of the retaining ring on the mixer (Cap-Screw.)
Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws. We were very pleased by the quick delivery of the part.
removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.
use your phones to take pic of how the wiring is to be reconnected, take pleanty from all angles
repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck
Gear-worm teeth stripped, teeth on pinion shaft worn to sharp edge and case gasket dried out. Not bad for a 20 yr. old mixer.
Looked at the mixer schematic form your website,which made it easy for me to take it apart. Once it was apart & all the grease removed I disassembled & cleaned all the drive parts. Saw what was warn, ordered the parts from you. Three days later received the parts, everything fit perfect. Added grease,assembled the mixer and it ran perfect, good for another 20 yrs. Thank you for making it so easy to repair an old mixer in just over two hours. Rolf
Replace went good used the online video, my husband doesn't usually use any help but said the video helped him. Now my mixer works perfect. Also the price and shipping time was awesome.
Attachments would not work, spindle turned erratically, with no power
Punched out the roll pin to remove eccentric from spindle, undid 5 screws (after removing trim ring), and removed 4 screws to undo the motor housing. Make sure to keep the one screw with a lock washer in the BACK of the housing. Undid the screw on top to remove the back of the motor housing to take out the strain relief grommet, prior to removing the motor housing. Scraped the excess grease into a tub to re-use. Pulled out the shaft, and lifted out the old (stripped) gear and plopped the new one in. Make sure to mark match points for parts, and put the pins back in in the right order. You have to put the 5 screws back in before sliding the trim ring on, and putting the roll pin back. make sure all gears mesh and test before snugging the motor housing screws. Be sure to orient the strain relief grommet securely, and be careful of the filter plates in the back of the housing (they're brittle). putting the grease back is like frosting a cake. Save a little for the planetary ass'y.