3HLER5437JQ3 Whirlpool Dryer - Instructions

First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to removed the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****

Step one: UNPLUG THE 220V LINE!
Removed the 2 screws on top under the lint door then flipped up the top. Next I unclipped the wire harness at the front and disconnected the 2 wires to the door switch and flipped the harness out of the way. Then I popped off the kick panel. Next, I removed the (4) 9mm screws holding the front panel on. The 2 lower screws only need to be loosened and the panel lifted off. Note the location of the door springs at the bottom. These springs can be reinstalled easily through the kick panel after you reinstall the front panel.
Next I removed the remnants of the old seal from the front panel but left the 3 plastic clips in place. The seal wraps around the perimeter of the panel and is held in place by the lip of the opening. The extra flap is then folded back so that the folded edge is toward the dryer drum and away from the front of the panel. The sketch in the instructions is not helpful!
Next, reinstall the front panel. As you set it onto the lower screws, you may need to lift the drum slightly to fit the panel into the drum opening. Tighten the 4 screws then reattach the 2 door springs. Test the operation by turning the drum counterclockwise by hand. Check to make sure the rear seal has not been displaced or damaged. That seal is actually glued into place. If it turns smoothly, snap the kick panel back on and reinstall the wire harness. Flip down the top and reinstall the 2 screws at the lint tray on top. Plug it in and give it a spin!.
Note, While you have it open, you'll want to use your shop vac and clean all the lint and pocket change out of the machine. You might as well take off the back panel and clean up in there and in the vent pipe too.
I didn't know if I needed a new belt but ordered one anyway. The old one turned out to be pretty well shot. After I had the front panel removed, replacing the belt is very simple. There is an idler pulley underneath that is under tension. Just push on the idler until the belt is loose. Switch the new one into place and you are done.

I removed the hex head screws from the back of the dryer and removed the back panel, after unplugging the dryer. I tested the various electrical components until I found that the upper limit temp fuse had gone out. Came to partselect.com and found the kit I needed and ordered it. When it came in, I replaced the upper temp limit fuse, and the other parts that came with the kit. I also, since the back was open, used the opportunity to vacuum out the blower fan and as much of the lint as I could get to. Dryer works great now!

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!

The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

Very easy to replace.

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.

Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!

Two screws hold the top control panel in place. Once removed the panel could be tipped forward. The Push to Start switch had 2 wires which were removed and swapped to the new starter switch. The old one rotated 90 degrees to remove and the new one installed. Panel was resecured to the top of the dryer and tested. Worked first time. Finding the part on the website, ordering it, receiving it quickly and the install couldn't have been easier or more pleasant or efficient.

Replaced the Thermal Fuse first - 30% chance - didn't help! Then I replaced the resistor - Not an in-kind replacement - looks different-Guessed the wrong place first [no specific directions :( ] and got some sparks - Yikes! Picked the second place and installed the resistor and it work PERFECT. Spent Less than $50 and back in business = GREAT!!

Unplugged unit and removed top and front of dryer. Removed drum and belt. noting how belt ran through the belt tension-er. Removed old felt seal from rear of drum. Replaced broken baffle, replaced rear seal. reinstalled belt. Put unit back together and test ran.

The repair was really easy and I loved the DIY videos they were great, not many tools needed to do these repairs that was great. The only thing is this didn't solve my issue.

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.