3EHD261MMWR0 Whirlpool Refrigerator - Instructions

I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old

took door of and replaced ,no problem

I followed the video that you have for this part and it was very easy to repair. The video that you put together showing how to do the repair, made the job very simple, and your service was outstanding. What a great web site!!! Thanks

I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks

Like most have stated this is a simple job. Nut-driver and six screws (on mine). Less than ten minutes. Like someone else said the hardest part was unloading the door.

Follow instructions from owners manual. top hinge first then move door upward and replace broken cam with new parts

Just as shown on a you tube video showing the steps involved, except I did not need to drill and tap the hole in the door. Cam repair kit contained all the correct parts.Freezer door is still working fine so I did not need to repair that door.

It was so easy I could have done the video. Many thank you's for saving me $79.00 in house call fees.... cindi

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Took out icemaker,it had been letting in too much water, foynd switch was not working anymore, ordered new one from PartSelect, got it in a few days,took icemaker out put new switch in & it is working like new. I was amazed I could still get parts for a 28 year old whirlpool. And with the help I got from PartSelect,I am really thankful. JoAnne, Easley, S.C.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Removed door,took out old part@replaced with new

I watched the how-to video on your website first and it made the job so much easier. Just remove the upper hinge, lift the door off, and replace the cam bushings on the bottom hinge. Put it back together in reverse order and your done! Thanks for having such an informative website! It saved me from buying a new appliance.

The parts were delivered promptly. I ordered the kit assembly because I didn't know which part was the problem. Reading the remarks from other people's symptoms and solutions made the process much easier. I replaced both the upper and lower cams. Lubricated the cams and reinstalled the door.. Problem solved!!!!

Empty the refrigerator door of all items and removable shleves.
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!