3ED26MMXRWR0 Whirlpool Refrigerator - Instructions

Took off all screws on box.Removed front of drawer,removed back-up to drawer and auger as one unit. Removed C-clamp on end of auger,this released all the parts. The end of the auger shaft unscrews, remove broken piece and reverse process with new part

hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.

Found auger was broken. Also found the ice cubes seemed too big and not breaking apart after the ice maker would cycle and dump in to the bucket. So I adjusted the ice cubes water feed timer making the cubes smaller and they are working real good through the auger now.Thanks for delivering the part so fast.........

(1)Remove all items stored in the inner door. (2)Remove all the shelves from the inner door. (3) Remove the top hinge cover screw and remove rhe hinge cover. (4) Remove the upper hinge (5) lift the door out of the lower hinge bracket and lay flat on a table or counter top. (6) Swap out the old parts with the new parts. (6) reassemble.

I printed your diagram of the complete assembly for reference when installing the new part. I was able to get the part number from the diagram and ordered it online. I received the new part in 2 days. I removed the ice from the ice maker's bin and kept it in the freezer. I removed the old drum and auger from the ice maker assembly and installed the new drum #4388736. I looked at your diagram to make sure I had all of the blades in their right orientation. After the drum and auger assembly was installed, I placed the ice that I had saved into the ice bin and slide it back into place. I then tested if the assembly would now drop ice and also if it would crush the ice, which i do not use very opten, because I know that using the ice crush mode will prematurely wear the drum assembly. The drum and auger gets much more stress when it is crushing ice. After the icemaker worked flawlessly, I rolled the refrigerator back into its regular position along side the cabinets. I was very pleased with the part and the excellent service that PartSelect.com provided. The price was less than I thought I would have to pay. Also, the company provides most of the individual parts of the ice maker assembly. Normally, when I would shop at a designated Whirlpool distributor, I would have to purchase the entire assembly costing 3 or 4 times higher than the price of the individual part. I, will now, always purchase my parts from PartSelect.com.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

My husband and I followed the instructional video on how to replace the "direct drive drum". We took note of how everything looked prior to dismantling the ice bin. We made sure we had the proper tools and a large flat surface to work on and started taking out the screws. Replaced the new drive drum part and put it all back together. The whole process took approximately 30 minutes and the ice crusher works great now. I'm a happy camper!!

I watched a video several time to get the steps in the removal and reinstall. It really was not that hard but first time repairs can take extra time.

Watched Video - took you through step by step

I took the tray out of ice maker, removed the screws holding the drum assembly. Dismantling the drum assembly careful as possible and placing the new drum on place of broken one, it still took twice to get it workable. Probably the next time I will follow the instructions a little more closely.

I was unable to remove the old part so I threaded the new part in front of it. They both fit within the actuator. Done!