3ED22DWXTW00 Whirlpool Refrigerator - Instructions

One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.

I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!

Took augur off broken bend put augur in new bend took 10 min now I can have ice. shipping was super fast.

Watched the video and viola, it was done. This was on the refrigerator side. Probably should have unplugged it, but didn't. One suggestion is hang a sheet in front to keep the cool in as best you can, even though it went really quickly.

Replace the auger drum. I had order it and the auger, but I did not need the auger. I returned the auger with ease. Parts Select will always have my business.

repair went good .only had problem removing tube from clip in front

Just loosened the screws at the top of the door hinge bracket, lifted the door off the hinge and set down on its side. Removed the broken cams, both the door cam & Cam on the lower hinge. Discarded the old parts after making sure the new parts would match up with the holes and screw holes would align. Installed a new cam on both lower hinge bracket and bottom of the door with new screws provided. Added some lubricant to minimize future wear and tear and re-installed the screws. Lifted the door back onto the lower hinge pin, Lifted up the pin on the top of door bracket until the pin would slid into the hole on top of door. Tightened the screws on top of the door hinge bracket. checked to make sure door sealed tightly around the perimeter of door opening and we were done. Total time was about 15-20 min. Anyone could do it. Thanks for the instructions and parts. Very pleased with the results. Sincerely, Jim

This is a simple repair. the only reason it took as look as it did was because you need to empty the products from the door(s). Of course this is a good opportunity to thoroughly clean the fridge. The problem was caused by wear on the plastic spacer for the bottom hinge. Remove the plastic covers that conceal the top hinge located on top of the refrigerator. Remove the three bolts that attach the hinge to the housing. The door can then be lifted off the bottom hinge. Remove and replace the bottom spacer. Then remove and replace the receiver in the door by prying it out with a screwdriver or pliers and popping in the new one. I put a dab of lithium grease on the hinges before I reassembled them to reduce the wear and extend the life a little. Reverse the procedure to reassemble.

changed bulb

The video on the site made the repair extremely easy. It took 15 - 30 minutes start to finish. Had it not been for the video I wouldn't have known that the plastic nut on the end of the auger was reverse threaded. I would highly recommend this site for ordering appliance parts.

pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

I have a KitchenAid side-by-side refrigerator and the right door clunked everytime it opened. We think it was damaged when contractors had to move the fridge and probably were too rough with it. I went on line and found that I could actually repair it myself (thanks to this web site, a great web site, by the way). I researched and found out through others that I needed a new door closing CAM kit. I only needed to fix 1 door, but bought the whole kit anyway (PS358690, Door Closing Cam Kit)to have spares. The kit showed up, I followed the great instructions via the video to remove the door, replaced the upper CAM on the door first and then ran into a snafu with the lower cam. The hinge on my model fridge does not have a replaceable CAM, it is physically attached to the door hinge. The instructions that came with the kit showed a hinge that was not my hinge - sigh. I had to put back all the old clunky parts, put the door back on and go order a new hinge (hopefully). Luckily there was a hinge available for my model with the CAM installed. I purchased it (PS331817, Door Hinge with Cam) and it came quickly like the other parts. I took the door off again (I knew how to do it this time), I replaced the hinge with ease, put the door back on and it is no CLUNK-FREE - Smooth like when we bought it. Thanks to everyone who wrote in about their clunking issues and thanks to PartSelect for the parts and the help.

I would not have attempted the repairs without your instruction. I use a Drimel tool with a abravise blade to cut the part off the shaft. After I realized the Drimel tool would work. It took me parhaps 10 minutes to get it off the shaft. I had already ordered the new part and the job was complete. Thanks for the help. Ron Burch

Went as planned. Video was such a great help. Delivery was in world record time. Price was right. Will use you again.

Followed the video, very helpful! Basically a walk in the park.