38489KBSMRSS General Electric Refrigerator - Instructions

easy pry out, disconnect wiring, connect on new switch and press in switch.

replace the bar lift top off

repalaced the old one with the new one. easy

I followed advice from other posts on this web site. The only thing additional I'd recommend is to take pictures of assemblies before you disassemble them. A neighbor gave me that useful tip. It should be noted that I first noticed my refrigerator failure back on June 22, 2012. I hired a reputable local repair service to fix it. They replaced the Defrost heater (item 618) and charged me $ 208.14. Then on August 22nd, I noticed that the problem resurfaced. I decided to fix it myself using info from site. The repair went well, and I'm hopeful that it will stay repaired. Kudos to this site!

removed freezer panel,found the evap.iced up,put defrost timer into defrost. wated five min.no heat used hair dryer to defrost evap.found termination visually defective.replace defective part.no call back.Iam a EPA certified universal technician.

Pulled the old gasket off, approximately 5 seconds. Put the new one in, starting from the corners, with no tools, approximately 2 minutes. Coated gasket with a thin film of petroleum jelly, approx. 1 minute.

I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.

Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.

Using Google search engine I was able to quickly locate the replacement rack for the refrigerator. When it arrived, I installed it by attaching it to the interior frame of the refrigerator.

took the old stop off put the new stop on

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Connected the 2 wires and pushed in the switch until it clicked.

per your instructions

My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!

HI I am Stoyan. I had a problem with my refrigerator. The freezer produces a lot of ice, but the refrigerator was warm. I try to find what other people comment on this site partselect.com. I decided that the thermostat is damaged. I ordered the thermostat from partselect.com and I had the delivery within 24 h. and I was very happy with the fast delivery service .I saw a video on the same site how they show how to do myself the change of the thermostat. I took the hairdryer from my wife to defrost the refrigerator for 40 minutes and removed the old thermostat. I decided to test the heater with a 9 volts electricity from a portable charger for a car. I made an electric circuit chain and on the end of the heater I saw that there was 9 volts electricity and I understood they are ok. I changed the thermostat for 5 minutes, looking very carefully to match the colors of the cables. For $ 11, I saved money to buy a new refrigerator or pay a big bill to a repair service. Thank you for the video that helped me very much. My refrigerator work well.