2DATW4305TQ0 Washer - Instructions

It was really easy, just follow the video. The washer machine sounds like new now.

After alot of helpful advise from you guys I replaced coupling water pump clutch, and the problem was still their. Then I tested motor capacitor and it appears dead. So I should receive new one tomorrow and hopefully success! I turned machine over and oil leak..so that's where the string with hose and air needle come in handy to put 90weight oil in through breather hole in gear case.

don't know, I ordered the part and my husband repaired it. Did not take him long at all.

The repair was fairly simple - the hardest part was taking the shell of the washer off and putting it back on.

Tipped the washer on its side and took the pump off then the motor then the coupling.

Pulled off the fabric softner holder, pulled out the cover for the agitator. Used a socket set to loosen the screw that holds in the agitator hub, pulled out the hub, removed the gasket from the cogs and replaced new cogs. Works like new!!!!

I purchased the part from PartSelect because it was very reasonable and it was OEM part. I have never replaced this kind of part on a washer so I figured it would take me a while. But PartSelect supplied a video showing the entire repair and that was the only reason I did not struggle with the repair. I will definitely buy any appliance parts I need in the future from PartSelect. Thanks Don

The most helpful hint was the video that I followed to a tee an if not I'd be treading in deep water. Very good but being a rookie it took me a hour an a half to complete, but it was my first voyage, of which should take 30 min if skilled a little bit. End results it works better than it has ever but always remember to keep track of all parts to replace it back in the right position. Thanks Again an I'll be back to see you if necessary for future reference!!!

slipped up upper locking collar lifted off cover and removed 7/16 bolt that holds agitator in place. lifted out agitator and installed agitator repair kit. 123 simple. also next day delivery outstanding keep up good work

I disconnected the washer from the water hoses and unplugged it. I laid it down on its back and the pump was right there on the bottom front. There were no clips holding the pump. With a pair of Channel Locks I disconnected the two hoses from the pump. I had to pry it off using a screwdriver. The pump shaft was rusty from the water leak so I wire brushed off. I put the new clips I ordered in place and pushed the new pump on. I then snapped the back clip on first because it was easier with a little tilt of the pump. I had to use my screwdriver to put the outside clip on. I reconnected the hoses put the wash back upright hooked up the water hoses and plugged it back in. I turned on and no leaks and is working good.

Disconnected power. Disconnected hot and cold, and drain hoses and placed in a plastic bucket. Pulled cover off the washer. Tilted washer onto its back. Removed 2 clips holding the pump. Disconnected wire harness from motor and removed 2 clips holding motor starting with lower clip. Removed a screw from the upper clip used for shipping. Set motor aside and removed broken pieces of the motor coupler from motor and transmission. The replacement part had a metal sleeve in the center of each white plastic ring. The old part did not. This required tapping the new ring onto both the motor and transmission shafts with a socket and makes for a tight fit. Reversed the process to put everything back together. Some alignment might be necessary to place motor to transmission. I recomment wearing thin work gloves to avoid nicks from sharp edges. I didn't. Washer is spinning again and sounds a lot better.

Partselect's video on how to replace the waterpump was great, but I was a bit stymied at the beginning as the control panel on my Whirlpool was attached differently than shown in the video. Mine was held on with two Phillips head screws in the back corners of the control panel. Also I'd suggest replacing the tub to pump hose (Part PS334685) at the same time-I wish I did. That hose was coated with crud which I cleaned out the best I could. All in all a pretty easy job-hardest part was getting cabinet back on (put the front bottom under the frame, then lower the cabinet onto the frame.

Watch the video on the part ordering webpage.

The hardest part was understanding how to take the cabinet apart. The "exploded" parts diagrams at PartSelect helped immensely.

I just followed the steps on the video, I was surprised how fast I got the parts within 24 Hrs . Thanks