14888W0 General Electric Range - Instructions

removed the old part with socket set and replaced the part with a fresh one. turned on oven, igniter heated up and oven lit.

The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best

Followed the instructions

By myself

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.

After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!

It was extremely simple! I removed the oven door and the storage drawer, unhooked the spring, and unscrewed the hinges. Removed the broken hinges and screwed in the new hinges, hooked the springs back on, slid the oven door back on and replaced the storage drawer! Presto! The repair is complete

used nut driver to remove old module and 10 minutes the cooktop was back in operation

Replaced the oven igniter

I'm still repairing. The igniter was replaced with new but it still doesn't glow. I'm waiting for a schematic that is being mailed to me from GE. In the meantime I have borrowed a test instrument to check that the system is hot when the BAKE button is pushed. The controls light up as expected but no glow. The BROIL igniter glows when activated, lighting the broiler. The new Ignite was packaged very well so it isn't suspect. I LEFT YOU FOR A FEW HOURS. I tested the electrical with a meter and got zero voltage. I removed the wire nuts and using two alligator clips I connected the meter to the bare wires coming from the oven wall. I then hit BAKE again and BINGO! Replaced the defective wire nut and now the igniter is happy as a clam. --- Thanks for your interest and for expediting the material.

took off the door it should be very simple by opening the door just a little bit then pull up the door take out the shellves than take of the bottom of oven usualy there's 2 cap screws in back holding it down then take out the drawer from under the oven & unscrew the bracket that holds the flame pipe from underneath also unscrew the screw from inside the oven the holds the actual flame pipe in front next to the door then unscrew the old igniter from the pipe snip the old wire going out from the igniter & strip it a little & connect the new igniter put on the ceramic cover supplied together with the new igniter connect it back to flame pipe put everything back together you should be done. But make sure the wires are pushed down to underneath as much as you could also when you put back the gas pipe the wire should not be in the way underneath the oven

Replacing the igniter was easy to do, that only took 15 min. The time was needed to take apart the bottom of the oven so I could get to the nuts on the igniter, and the time to put it back together again. I'm very inexperienced at this sort of thing so since I could do it I'd encourage anyone to give it a go, and anyone that knows what they're doing will do it much faster.

1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.

It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.