Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drive ring disintegrated
Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good enough.
Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.
My son-in-law is our handyman. He diagnosed the problem, found us the part and then put it in. The part came several days before we expected it and the whole thing went very well and we saved lots of money!
The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.
Remove 2 screws, and GENTLY remove tray. There are two motors on the back side that are wired in to the back of the fridge. Unplug the harness and the whole assembly will come out. Take note of the way the plunger comes out, if not, it will take a little more time to figure out. reassemble motors onto new tray then GENTLY slide into postion, with one hand plug in wiring harness then seat tray into position and reinstall screws. Done.
Ice maker auger wouldn't rotate, motor worked fine
To replace the broken drive coupling on the motor end of the auger requires sliding the ice bin out of the freezer section of the refrigerator. Remove the ice cubes and let it thaw out for a few minutes. Remove five screws holding the front face on the ice bin to remove the ice auger. slip the new drive coupling over the end of the auger. reassemble and replace the face plate with the five screws. Slide the ice bin back in the freezer. Less than fifteen minutes it was finished.
Repair was relatively easy. I found several videos on You Tube on repairing or replacing Solenoid & Ice Maker Auger Motor. They weren't broken but those videos show how to replace them and remove ice enclosure, which was the part broken. Only issue was removing yoke off the motor. It has reverse threads and videos had shown holding shaft of motor with needle nose pliers to hold it while you thread off the yoke. You need good needle nose pliers with teeth on them or the shaft will slip in them. I had to go buy new pair while repairing. It's all goes back together perfectly! I took pictures of the assembly, before I removed everything and needed to refer back to them when I was reconnecting the wires.
I pulled the dispenser bin and emptied the existing ice (the maker worked, the dispenser would not dispense). Though there appears to be more, there are about 4 (reciting from memory)very small tap screws holding the front of the dispenser unit to the bin. The dispenser activation screw mounts over protruding items at each end. The item at the back (away from the dispenser gear package) is the drive ring that was broken. The drive ring is a small plastic cup that inserts into an opening at the back of the bin (female side to the rear) and slides into the distal end of the activation screw on the same end. One must line up the small slot on the inside of the drive ring with the end of the screw. Slide the assembly together (make sure that the cube/crush switch rod is properly clipped in place with the return spring hooked to the clip), GENTLY install the 4 or so screws and return he assembly to the freezer. It should work flawlessly. Elapsed time: 15 - 20 minutes.
Ice maker would stop dispensing ice,shaft would stall.
Checked the ice tray and could only find the drive ring had some breaks in the plastic. Actually did not see why this would stop the auger from turning and dispensing ice. However this was the only thing I could find wrong with the unit. I pulled the tray, removed 6 screws (star tip heads) pulled the auger forward and replaced the drive wheel, put the unit back together and its been working fine ever since.
Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.
Ice enclosure tray was broken where auger motor mounts to it.
First Remove ice holder, now take out nut left side under tray, remove tray from mounts, unplug wires, remove tray from freezer, remove solenoid assy from tray try to keep it from coming apart, remove motor from tray, the auger yoke is on a shaft that has to be removed by turning it clockwise (reverse threads). i used a small Chanel lock to hold shaft when removing yoke, Now remount the motor and yoke, remount the spring loaded solenoid assy, slide the ice bin enclosure back in a ways, then reconnect the wiring harness, remount it rest of the way in, install the nut. and your good to go.