Models
>
12001749
12001749 Maytag Refrigerator - Overview
Sections of the 12001749
[Viewing 1 of 1]Exact Part matches for your search term
[Viewing 2 of 2]
DISCONTINUED
This part number matches the current model number 12001749
PartSelect #: PS46254
Manufacturer #: 12001749
No Longer Available
Bin/enclosure enhance
This part number matches the current model number 12001749
PartSelect #: PS12633670
Manufacturer #: 12001749
No Longer Available
Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Ice Bucket Housing
PartSelect #: PS11743212
Manufacturer #: WP61004881
This is the tray that holds the ice dispenser.
$167.96
In Stock
Ice Bin Drive Ring
PartSelect #: PS11743163
Manufacturer #: WP61003336
This drive ring is three inches in diameter. It is all white in color and is made of plastic. This ring is used with a refrigeraor's icemaker assembly.
$47.77
In Stock
Ice Bucket Support Enclosure
PartSelect #: PS2060969
Manufacturer #: 61005625
This part holds and supports the bucket that holds the ice when dropped from the icemaker.
$165.77
Special Order
Ice Dispenser Engagement Yoke
PartSelect #: PS11743333
Manufacturer #: WP63052-2
This ice dispenser yoke is an inch and a half long. It is made of metal and is used with the ice enclosure of a refrigerator's icemaker assembly.
$39.17
In Stock
Ice Bin Access Door
PartSelect #: PS2060194
Manufacturer #: 61004776
This ice bin access door is nine inches long and six inches wide. It is clear in color and is made of plastic.
No Longer Available
Ice Door
PartSelect #: PS2059826
Manufacturer #: 61004327
This is the front of the icemaker bucket that holds the ice. It covers the front and the only opening is where the auger would dispense the ice.
No Longer Available
Questions And Answers for 12001749
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 12001749
[Viewing 2 of 2]Ice maker won’t dispense ice
Fixed by
these parts
these parts
Show All
Ice maker not making ice
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice-maker had ice, but did not dispense the ice when pushing in the button.
First I removed to ice-bucket and noticed the plastic that holds the motor with a head of what I would call a two-prong fork had broken off the plastic (enclosure). Thus it lost contact to the ice bucket's screw that pushes the ice forward when the dispense button is pressed. After ordering a new enclosure I had to remove one screw nut
... Read more
and pull the wire plug (to the motor) out carefully. Then I had to remove eight screws holding the motor and related parts to the old enclosure and attached it to the new enclosure. The only tricky part was taking that fork off. It screws off, but in the opposite way. Also, I had to get a pair of pliers to hold the turn shaft from turning when taking the fork off.
Read less
Parts Used:
-
mark from marietta, GA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
42 of 43 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Yoke auger tore hole in plastic ice enclosure
Very simple repair. First Remove ice tray. Next remove enclosure. Believe there were 3 screws to remove enclosure (1 bottom, 2 top). Slide enclosure out slowly to gain access to power connector mounted on back wall. removed components from enclosure (motor and solenoid). Take extra care removing solenoid with spring/rod as it is 3
... Read more
separate pieces (spring, rod, and coil). Easy to figure out reassemble but easier if you take note during disassembly. Took me a while to get yoke off from motor assmbly. noticed they were reverse threads (lefty). So to remove yoke from shaft had to turn CW vs CCW on regular threads. Once had yoke off, rest of assembly was easy. Mounted motor, reinstalled yoke. Put entire re-assembled enclosure back in fridge. Slide in part way, to give yourself plenty of room to plug power connector in. Reattach assembly with 3 screws. Works like a champ.
Read less
Parts Used:
-
Craig from East Fairfield, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
36 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice auger motor broke away from the ice enclosure
Quiet a simple repair. First I removed the ice maker bin and the plastic side panel on the right hand side. From there, I was able to remove the ICE ENCLOSURE . It unhooks. Next I removed the ICE DESPENSOR ENGAGEMENT YOKE. It has reverse threads so be careful. Next I removed the ICE AUGER MOTOR. Its located at the back of the ICE E
... Read more
NCLOSURE and held in place by 4 phillips screws. You also need to remove the SOLENOID YOKE ASSEMBLY which is located just to the left of the ICE AUGER MOTOR. It unscrews with 2 phillips screws. Next I reassembled the ICE AUGER MOTOR and SOLENOID YOKE ASSEMBLY to the new ICE ENCLOSURE. Then I reinstalled the ENGAGEMENT YOKE and snapped the unit back in place.
Read less
Parts Used:
-
Thomas from Granite Bay, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
28 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!