Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Take pictures along the way. 1. Remove lower front panel using screwdriver to lift up on tabs on top of panel. 2. remove door 3. unplug moisture sensor plugs 4. remove lint trap 5. on back of dryer, remove screws holding upper lid 6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on 7. remove the front panel screws mentioned in step 6. 8. Remove lower front panel screws 9. remove front panel 10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys) 11. slide out tumbling drum 12. with drum removed, use socket wrench and socket to remove old idler pulley. 13. install new idler pulley 14. reinstall tumbling drum 15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley. 16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly. 17. Reinstall front panel 18 slide top panel back into place and secure with screws from back 19. reinstall door 20. reattach moisture sensor plugs 21. reinstall lower panel
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Dryer door latch broke and door wouldn’t stay shut.
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.
Old. Original heat seal was deteriorated and peeling off. Streaks were getting on the clothes.
Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.
This could not have been easier. The hardest part was tipping the dryer over on its' side. Instructions: 1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor. Insert leveling foot into the foot opening on the bottom of the dryer & screw in with fingers until it is difficult to turn. 2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level. 3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position. 4. Use a level, back to front & side to side, to determine if feet need further adjustment. 5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.