1106907100 Kenmore Dryer - Instructions

I was very pleased with the shipping speed, the belt arrived in less than 24 hours! The installation was very easy and if you need help the video on the belt info page should be helpful.

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

I had to take the top loose and raise it up. There are two screws in exhaust vent you have to take out then you can raise the top. When you raise the top you will have to take the front loose and open it up enough to take the drum out. Go to the back and take the lower cover off and take the screws holding the exhaust vent out so the vent will come out the top. When you take the vent out you will see a fan on the end of the motor shaft. The fan is threaded on the shaft and it is left handed threads. As you face the fan you will have to turn the fan to the right to get if off. You will need someone to hold a back up on the motor shaft inside the dryer to keep it from turning. Take the motor out then get the new motor and wire it according to instructions. Install the motor on the motor mount, put fan on then put everything back in reverse order that you took it apart. The hardest part for me was putting the clips on the motor when I put it back together. Hope this helps you.

You pop the top of the dryer. Remove to hex screws which allow you to remove the front panel. Next you pull the drum off, snack the belt around the drum, motor and tension pulley and reverse the steps. The hardest part is getting the drum back in place without knocking the belt off the motor.

Unplugged dryer. Removed lint tray screws. Opened top of dryer and removed the two face screws then removed front of dryer. Released the belt tensioner. Then removed the drum. Disconnected the wiring clip and with a creseant wrench held the back of motor and turned the nut in the front clockwise to loosen the motor from the vent fan. Then simply pulled the old motor out and reversed the steps and now have a great working old dryer again.

I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

Fast shipping. Part arrived the next day!

I followed the instructions you supplied. All went well. The short movie that you supplied was fine but the only tricky part which included placing the belt over the idler wheel was not well done in that the repairman's arm covered the work area. Delivery time was excellent.

This is a long, sad story, but I'll cut to the chase. I was told by few appliance repair guys that my problem was most likely due to the motor being bad. I had checked the thermal fuse, the door switch, and the power switch, and all were good so that made sense. I then saw a video which made it seem fairly straight forward to remove the old motor and replace it. So I ordered the motor from Part Select. Turns out it's impossible to remove the motor without also removing (and replacing) the blower. The video never mentions that. Also FYI, I found out that my dryer switch WAS broken, and nothing was wrong with the motor, so I spent $250 on a repair that should have cost %40. Oh well ...

It snapped right in. Works perfect.

I watched the You Tube video on this site. The only issue is there is a plastic fitting that I seriously damaged trying to remove the motor from the blower. You have to hold the plastic fiting stationary while turning the nut on the other end of the motor. If you try to rotate the plastic fitting you'll destroy it as I did. I got it loose by squeezing the plastic fitting with a large pair of channel lock pliers and then rotating the nut.

I was able to take apart the dryer myself and get old belt out, then my son helped me remove the drum and put new belt on. Well worth fixing; it works great again and the part with shipping and handling was only $17.00! better then price of new dryer!!!Thanks, Mary ( Cincinnati)

So glad we tried the belt and rollers before going out and buying a new one. Very quiet now,so happy!

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

replaced the belt