1106907100 Kenmore Dryer - Instructions

Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

Went to YouTube It was real easy.

Repair went fine. Really easy for the most part. Unfortunately it didn't solve my problem. Great place to get parts though. I'm going to continue my search for the source of the noise

Thank you for the the installation tip I received along with the part. The suggestion of removing the front panel to install the belt made the installation go very smoothly.

I unplugged the dryer then removed 2 Phillips screws from lint trap. Then I popped the top up on each top corner with a screwdriver. I removed the 2 screws holding the front cover. I unclipped the wiring connection and moved the panel. I took out the old belt, put the tensioned back on then put the new belt around the drum and held the drum up with my shoulder then put the belt through the tensioner and put it on the motor spindle by pushing the tensioner back. I put it back together and it worked perfectly. Your video was very helpful. Job was very easy.

Had my wife call the repair man. Since it was Saturday afternoon, no luck. YouTube help me diagnose the problem. I found that the drum belt slipped off the idler pulley assembly and the assembly was laying on the floor. I noticed that the belt was frayed and was probably stretched out which may be why the belt slipped off in the first place. I glued the frayed pieces of the belt back with gorilla glue and clamps. You Tube helped me mount the idler pulley assembly and string the belt correctly. I then ordered the replacement parts through your website. The parts came to my home in a few days and I will fix the dryer properly when I get a chance.

The instruction sheet that comes with the parts is excellent. Follow it and all goes well. Be patient and stay away from the sharp sheet metal edges present in all such appliances !!

I didn't have to remove the entire door...I just removed the screws with the door open, used a needle nose plier to remove the plastic insert..stuck the new one in. Then I replaced the metal portion by popping it out and inserting the new one. Easy

It Went well Part was very fragile

When I got the door catch, I held it in a pair of pliers and pushed it right into place. The door would still pop open. After awhile, I realized that the door was bent, probably by a small child climbing up on it. I had to loosen some of the screws that held the door on in order to relieve the tension in the door so that it would stay closed. As long as it continues to work, I won't worry about replacing the door. It's in a rental house anyway.

I got my kit and when I opened it the exact parts were there!! I am a older woman and was a little worried that I could do it. I took the pliers and pulled the old latch catch out and 1-2-3 walah!! It was so unbelievably easy. If I can do it anyone can. Thank you for saving me hundreds of $s on a new dryer.

I watched the video on the computer and it was very easy to repair I had the dyer apart ,fixed and put together in about half hour