11068062801 Kenmore Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer kept shutting off after 10-15minutes
Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.
Parts Used:
-
Neal from Bertha, MN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
lint filter housing cracked
open dyer door replace lint filter perfect fit, good price, fast delvery. thank you
Parts Used:
-
Richard from Sanford, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The door catch had broken and would no longer hold the door closed to allow the cycle to start.
The door catchh is easily removed by sqweezing the base and pulling out through the opening from where it was installed. The replacemet simply installs in reverse order. There are two such catches on the door. Reversing the catch from the hinge side of the door will help keep you going until the replacement parts arrive. I suggest ordering two replacements and keeping the used parts for temporary use if you should have trouble again.
Parts Used:
-
Mark from Howard Lake, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Dryer Door Catch Very Worn. Plastic Keeper That Holds Clip In Line Has Broken Off The Back Of Catch.
Took my channle locks and pulled old catch out and snapped in new catch. Works great now. Cost me four dollars and 3 minutes of my time.
Parts Used:
-
MARK from FORT WORTH, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
door catch broken
-
Stephen from McKinney, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The leveling foot on my dryer broke.
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.
Parts Used:
-
Diana from Clifton, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Suspected bad moisture sensors
Opened machine up, removed electric control panel, removed door assembly, removed lint collector assembly, removed and replaced 2 sensor bars then reassembled machine. Ended up not being the problem but, I now have new moisture sensing bars.
Parts Used:
-
David from Sussex, WI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Lint filter tore causing hang up with metal guide
Removed lint filter cover (3 screws). Removed old lint filter. Adjusted metal guide. Reinstalled lint filter cover (3 screws). Installed lint filter. Replacement filter is a like quality.
Parts Used:
-
Mark from Layton, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lint filter gasket broken
-
Bob from Howell, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dryer door would not stay closed
Removed door catch and installed new one. Easy as pie, after watching installation video.
Parts Used:
-
Robert from Fontana, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
seal broke in dryer door
soooooooo proud of myself!!!! cause I correctly ordered and correctly installed seal on door on clothes dryer
Parts Used:
-
Caroline from Pulaski, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The door catch had broken.
When the part came in it was really simply. All I had to do was push the new catch into the hole and make sure it was in all the way and secure. A repair man would have charged at least $65 and it took me all of 1 minute to do.
Parts Used:
-
Braham from Scottsdale, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The seal on the lint filter was not well attached
Replacing the filter was easy - the new filtes's seal seems much more secure. The new one works much better than the old one.
Parts Used:
-
Kathleen from Dyke, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Felt around the Lint Filter was loose and would not stay
-
Janice from Central Lake, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
broken dryer door latches.
It was simple. Originally, (just like a man) I took the door apart and removed from behind. THEN I WATCHED THE REPAIR VIDEO!!! Boy did I feel like a dummy. The repair was simple and easy. Putty knife popped the latch out and popped a new one in. Got a couple of extras for future issues. Both latches had failed previously, oddly, only 1 is actually used. Oh well, repair done, bride happy, all is well. Thanks Parts Select. Moral of the story, WATCH THE REPAIR VIDEO FIRST!!!!!!!!
Parts Used:
-
David from West Sacramento, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!