11067422600 Kenmore Dryer - Instructions

Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Will be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob

Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.

Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.

Dryer didn't heat. I got the heating element thru sears and when I ordered it I thought I should also order the thermostats but I didn't. Element arrived two days after ordered right on time. Slipped right in in a few minutes. Turned dryer on. No heat. Went back to drawing board. Watched videos on part select site and realized I needed thermostats. Ordered them and lint filter. Arrived right on schedule and also slipped in in no time flat. Turned dryer on and yes it heated perfectly. Wife was pretty impressed with new lint filter as other one was torn with jagged edges. MY SUGGESTION: if your dryer doesn't heat and you can't test each individual item thermostats and heating element order the three of them ( high limit and cycling thermostats and heating element) cause they'll probably will all go at the same time anyway. Then won't have to wait on the second shipment if things don't work with partial replacement. Parts select was great and videos are well understood and easy to follow. Would certainly use again.

Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.

I watched all the videos with Steve. He was very helpful in his presentation of the repairs. Due to the age of the dryer every thing was replaced and was very easy to do. Thank you Steve and PartSelect for making these repairs possible and easy

The dryer quit working. I did some trouble shooting on your amazing site, ordered what i thought it might need and then got to work. Took no time to get it apart and replace roller kit and belt. What took the longest was getting in there and cleaning out probably 15 years worth of dirt and dust. If you have not opened your dryer up and done this, 10/10 recommend, because in doing so i found that the motor was the real culprit. Once i opened it up more, especially cleaning around the blower fan and motor, i was half a day in. Put it all back together and got it running for two more loads before the motor quit. Replaced that and since the hard work was done, had it back in in half an hour and running great. Probably will need to redo the felt seal one day, but for now, i am calling it a win. This is my go to site for all things and i have been able to work on most of my major appliances and do it myself using the helpful information here.

Be very careful of burrs on the edges of the steel inside the dryer. I cut myself badly when reaching into unplug the switch.
Procedure: Lifted the dryer top by pulling forward and rotating front up. Removed 2 philips screws holding the switch at the door. Reached into dryer and unplugged bad switch. Inserting small blade screw driver at the edge helped release the plugs detent. Installed new switch using reverse of above.

I knew that the dryer needed a new belt and since the dryer was also failing to dry the clothes in one cycle, I decided to replace the three thermostats, figuring that I might as well do all three if I'm going to open up the dryer. I downloaded a schematic of the dryer from the Whirlpool web site, which helped me to order the right parts and see how I would be able to make the repairs. Once I figured out how to get to the drum for the belt replacement, installation was quite easy.

First step was to unplug the dryer, remove the vent hose and remove the back panel with a nut driver. Once the back panel was removed, it was easy to see all three sensors. The heating element unit was easy to remove - two screws. This made it easier to replace the sensor. Each sensor was shaped differently, making it easier to decide what went where. This normally would not have been a problem, but the part numbers have changed for this dryer. I could have also cross referenced the parts by using the partselect.com web site.

To access the dryer drum, I had to remove two screws on the back of the dryer that are located in two tabs that hold the control panel to the dryer cabinet. Once removed, it was easy to lift the top of the cabinet and swing it up and against a nearby wall for support while I replaced the belt.
I removed the old belt from the motor pulley, and then just removed the whole drum. I placed the new belt around the drum, placed the drum back in position. With my wife supporting the drum, it was easy to bring the belt through a guide and slip over the motor pulley. Then, I rotated the drum manually to make sure the belt wasn't twisted.

After ten minutes of putting everything back together, it was time to plug in the dryer and test it. I did it without a load first and checked the vent for hot air. After that, we did a couple of loads...one on high and one on perma press, and when the cycle was over, the clothes were dry!

Delivery time from PartSelect was super fast! Prices are excellent, and I really appreciate such a helpful web site. Anyone with a small amount of mechanical ability and "do it yourself" experience can save $$$ by fixing it yourself. Having someone service this dryer would have cost me more just to replace the belt.....let alone the added insurance of replacing the sensors. And, I learned that if the heating element should fail, replacing it would be a snap, and would start with a visit toe partselect.com!

1 screw to replace.

I ordered the belt idler pully and drum support rollers and after watching the video on Parts Select web page, changed the parts. It could be done by one person, however having a second person to help with the drum installation worked great. I discovered the motor bearing on the front side of the motor was the source of the squeek. I disassembled the dryer again and removed the motor. After ordering a motor the installation and reassembly went smoothly. The parts came in two days of placing the orders and virtually new parts in the dryer makes it seem like a new machine.

Followed the video .... Also installed another part. which was a kit. the video here showed the third wire being installed. The video on repair clinic did not show where to attach the third wire (orange wire). The Kit and the Thermostat was installed with 25 mins. Thanks

Followed video on Parts Select site for comparable model showing roller and drive belt replacement.

The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.

First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to removed the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****