11065062500 Kenmore Dryer - Instructions

I ordered the part, watched the video and made the repair in less than thirty minutes. This was much cheaper than purchasing a new dryer.

Pull off the front panel of the dryer, and replaced the thermal fuse. Very easy. Plus, vacuumed out the whole inside of the dryer, the rear and the tube running from the dryer to the outside. Will be doing this at least every 3 months to be safe. You would be surprised at how much lint builds up inside the machine. Eve though we clean the filter trap after every use of a load of clothes.

I followed the directions on your site. I pulled out the filter on the top of the machine. Then removed the two screws where the filter is located, I am not sure I would have found those screws had it not been for your directions. I then pulled up on the top of the machine by grabbing the sides near the front of the top, it came right up. I then raised it enough to place a broom handle to hold the top up so I could reach the switch. I removed the two screws holding the switch and then pulled the connector apart. I then replaced the switch with the two screws and plugged the connector back together. Removed the broom handle and closed the top and replaced the two screws I removed by the filter. Replaced the filter and started the machine running and opened the door and it turned off and the light came on. It took me about twenty minutes.

Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.

Had husband of 55yrs.replace the switch VERY SIMPLE!

I simply unplugged the dryer and removed the backing. Once off I located the part which was in plain sight, unhooked the wires and attached them to the new part. Put backing back on plugged it in and turned it on and it worked.

Opened machine up, removed electric control panel, removed door assembly, removed lint collector assembly, removed and replaced 2 sensor bars then reassembled machine. Ended up not being the problem but, I now have new moisture sensing bars.

Removed lint filter cover (3 screws). Removed old lint filter. Adjusted metal guide. Reinstalled lint filter cover (3 screws). Installed lint filter. Replacement filter is a like quality.

Goggle the make and model and videos were available on how to remove the lid. I would not have know how to otherwise.

remove back of dryer and install new part

First I take off the top panel , then take out four screw of console panel and disconnected wire from machine electric panel . Now I take four screw of door panel , disconnected door switch and take door panel out . Next step is to take 2 screw at blow housing and take this part out . Now I have enough room to take off two wire of the old thermal fuse and thermistor without removing the drum . Pull out old thermal fuse and thermisor , install the new one, reconnect two wire for each of them and reinstall all of part I take out before .The dyer work good after that but in the next day the dyer won't start again .I some time hear the sound bip bip together with the light from console panel even though I don't press any buttom at all .I thought either machine control electric or user interface die . As a new customer of partselect , I would like to hear any idea from you . Thanks for reading .

Took 12 screws off the back. One screw for the fuse. $9.32 and 30 minutes and we're back in business!

replsce

First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys

Well the video showed us taking off the back. Which wouldn't come off. Welded. Then we could not find the fuse in back of the unit or bottom. The second time we tried we found it in the front. We had to take off the front, bottom cover then we found the fuse. But, it didn't fix the problem. The unit is still on Casual load only. When we push the buttons the other lights light up but goes back to Casual. The unit is clear of lint and still drys but only at the Casual setting.