Models > 11060902990 > Instructions

11060902990 Kenmore Dishwasher - Instructions

All installation instructions for 11060902990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060902990
16-30 of 394
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would not heat at all.

  • Customer: Lou from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 22 people found this instruction helpful
Found a service manual on-line for the Whirlpool Duet Dryer. Did the troubleshooting for the problem stated. Found the heater element to be bad (open circuit across heater block). Ordered new element from PartSelect.com and installed. Dryer now works like a charm and I didn't have to call a repairman.

Rear tub seal failure

  • Customer: Jerry from Everett WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 22 of 30 people found this instruction helpful
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine

dryer works but no heat.

  • Customer: Tom from Grove OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 20 of 25 people found this instruction helpful
Measured resistance on thermostats & heating element. Found thermostat open so ordered replacement part and heat again.

The dryer was running and it quit, just stopped. A friend looked at it and thought it was this switch. I purchased the switch and he installed and it still did not work.

  • Customer: Debbie from Mooresville, IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 17 of 19 people found this instruction helpful
No, if that had of been the problem, it would have worked. However, I called a service man out to look at it. It was a fuse that does not look like a fuse. I had the system already torn apart and cleaned. The service took a meter and checked the fuse ( that did not look like a fuse) and it was bad. It cost 14.00 for the fuse, it took less than 5 minutes for installation and the service fee was $65.00. My advise, get a meter, check everything yourself, and only purchase what you need.

Needed to change rear exhaust to the side to fit dryer into my closet.

  • Customer: Mark from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 30 of 59 people found this instruction helpful
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.

Timer not working

  • Customer: erik from wasilla AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 17 people found this instruction helpful
Repair was straightforward. When I got the old timer out, I found the problem. Two small screws secure the geardrive for the timer to the electrical part. One of the screws had vibrated loose and allowed the gearbox to float away from the electrical board, so the gears werent meshing and the little ground tab inside wasn't touching the metal geardrive housing. In short, I would recommend removing your old timer and diagnosing the problem. before spending $100 on a new one. If I had done that, I could have just tightened the screw back in and saved myself the $$. Just FYI

Dryer motor runs,drum turns but no heat.

  • Customer: Arron from El Reno OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 17 people found this instruction helpful
Removed the back of the dryer. Used a multimeter set to read Ohms to check each Thermal cut-off switch. Each one read with continuity and some resistance. The one that was bad read open. So i replaced this one and the other one that came in the kit since i already paid for both.Then i replaced the back ran the dryer and it worked great.

Heating element burned out

  • Customer: Derek from Springhill LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 15 of 18 people found this instruction helpful
I first went to your site and studied the parts diagram to see where the element was located. I then unplugged the dryer and pulled from the wall. After that I popped open the front cover and accessed the bottom of the dryer where the element was located. I then removed two screws that held the element in place and removed the wires to the element. After a little tug the old element came out. I slid the new one in place and connected the wiring and screws and replaced the cover and pluged it in. Works good as new...

Lid closes, switch wouldn't turn on machine.

  • Customer: Kenneth from Wilmington IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 14 of 17 people found this instruction helpful
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.

Very Loud Squeaking Noise

  • Customer: GREGORY from Wilsonville OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 17 people found this instruction helpful
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. Easy repair 15-30

Thermal fuse was bad.

  • Customer: Brad from Odessa MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 13 of 17 people found this instruction helpful
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.

Thanks for the help.

Washer would fill up, wash, then stop

  • Customer: Glen from Plano TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.

The dryer stopped working and would not start.

  • Customer: kevin from Saint Augustine FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 11 of 12 people found this instruction helpful
After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet metal screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.

broken belt

  • Customer: Larry from exeter RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 16 people found this instruction helpful
First I removed back and top of dryer, then the support braces holding the drum, after that I took the drum out and the blower covers and cleaned the whole dryer of lint and other debris. Installed the new belt and then reassembled the dryer.

Poorly designed lint filter/ gasket falls off

  • Customer: John from Madison WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 16 people found this instruction helpful
Replaced
All Instructions for the 11060902990
16-30 of 394