11060232002 Kenmore Dryer - Instructions

1. Shut off power to dryer 2. Remove back panel covers with 1/4" nut driver 3. Use ohm meter to determine continuity at various thermal couples (3) and the one thermal fuse on the blower panel. . (This was the "bad "one in my case) 4. Remove two wires and remove the one screw that holds fuse. Did not have the model# for dryer, so I took the part# from the blown fuse and found it at partselect. Com. . They even showed an exact picture of the part I needed. . Ordered on tuesday/arrived by fed x on saturday. . . Reverse procedure to install. .

Follow instructions from online video supplied by Parts Select. Repair went very smooth!! Dryer started up and I am back in business. Thank You Parts Select!

After I received the new belt I un-plugged the electric cord and shut off the gas supply. I pulled the dryer about 10 inches away from the wall to remove the vent duct from the back of the dryer. Used the putty knife to release the clips on bottom front panel and a screw driver to pop the front of the top at the left side and right side, removed the two Phillips head screws under the lint door, then lifted the top to the vertical position. Loosened the hex head screws at the bottom of the upper front panel (don't take them out). At the top back side of the front panel, pull off the electrical wires from the door interlock switch and pull the retainer holding the wires to the front panel (don't take the plastic clip from the wires.) Place some wood blocks to support the drum at the front of the drum. Use the nut driver to remove the two screws on the inside at the top of the front panel. Disconnect the two springs that hold the door closed. Lift the panel from the two loosened nuts at the bottom and pull it away from the drum and let the drum settle on the blocks of wood to support it. Place the new belt around the drum lining it up where the old belt left its mark around the drum with the grooved surface facing the drum. Replace the front upper panel with the door to engage to two tabs on the screws you left at the bottom. Lift the drum so that it engages with the opening in the front panel. In case where the drum had dropped too far, use the putty knife to engage the felt flange at the rear of the drum with the rear cabinet flange. Reinstall the two screws at the top that you had removed. Reconnect the two wires at the interlock switch and snap the clip with the wires to the flange of the upper front panel. Replace the door springs on the hinge extensions to the flange at the bottom of the cabinet. Set the Idler pulley assembly into the cabinet floor sliding the end tab into the slot and the two tabs fit into the holes in the floor. Pull a loop of the belt under the idler pulley and then pull it toward the motor pulley. You might use the shaft of your Phillips screw driver instead of you fingers to get it around the pulley on the motor shaft. Turn the drum by had for several complete turns to ensure that the belt lines up on the drum and that the drum isn't binding on the back or front seals. Close the top, snapping onto the top of the cabinet. Plug the dryer into the electric outlet and set the timer to Fluff Air range and push the start button with the door closed. The drum should be turning smoothly. Open the door and all should stop. Reconnect the Vent and move the dryer back to its former position. Turn gas supply on but do not start the dryer. Check for gas leaks. If you find a leak in either at connectors or the flexible connecter call a qualified contractor to replace the flex connecter. Otherwise you can then set for one of the dryer settings and push the start button and observe the burner through the lower panel to see that the igniter is lighting up and finally the gas turns on and a decent blue flam is burning in the combustion tube. Open the dryer door and the flame should cut off and the drum stop turning. You are ready to set the bottom panel. Set the panel on the two lower tabs and close it upward until the snaps lock it in position. Job Done

I replaced the Thermal fuse and this fixed the problem.

pop the top of the dryer open with a screwdriver(front), leatherman works well, unscrew the old switch,disconnect the wires - new part has 3 wires old one has 2 but the connector fits fine. closed up the dryer. turned it on. it works fine. A long phillips head is suggested (8") to clear the door frame so you don't beat up your knuckles.

Ordered your fuse & thermostat. Total $37.29, installed parts & still no heat. Ordered your 240v Heating element.. Total $77.43, installed part & still no heat, Removed 30amp circuit breaker and purchased replacement for $11.30 in town. Installed breaker, dryer now has heat. Still smiling as I keep telling my self I performed preventive maintenance on my dryer!!!

I followed the video directions exactly as instructed and I had no problem doing the repair myself. And if I can do it being a woman with no help you can do it. Easy peasy~

1.Installed thermal fuse. I thought this was the problem as a few years ago this fixed the dryer that was now experiencing a similar problem. Problem persisted. 2. Installed new thermostat. Problem persisted. 3. Installed new igniter coils. Eureka! Problem solved!

I simply pulled the dryer away from wall. Cleaned vents. Pulled plug out from outlet. Unscrewed the back panel and removed the cycling thermostat and fuse as per your instructions. Since I had the back panel removed I cleaned the inside of lint as well. Put the back panel back started the dryer and everything was perfect. Saved myself at least 150.00.

I ordered the part I suspected....which was indicated by approximately 44% of the users having success replacing the thermal fuse. After watching the video on how to perform the repair, it was a snap! Removed the 9 screws, removed the vent hose, popped out the fuse, and replaced it. After checking to see if that was the problem....which it was, I reassembled the dryer. It only took more time because I chose to vacuum any exposed areas. THANK YOU!

Opened top, removed front panel, snapped in new ring bearing, reinstalled front panel and top.

It was not hard at all. I got the parts the next day.

Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

unplug take off vent hose and back panel unscrew one bolt holding the fuse disconnect 2 wires. Connect the 2 wires to the new fuse hold in place with the bolt put back on the back panel and vent hose plug in and your done