Models > 11060232002 > Instructions

11060232002 Kenmore Dryer - Instructions

All installation instructions for 11060232002 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060232002
1,186-1,200 of 1,258
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

would no longer heat

  • Customer: Terry from Kaufman TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went online looked up whirlpool and got the phone number and called them told the person on the phone the model number and Ineeded a heating element Igave credit card information had my part in 2days .put that in and discovered Ialso needed athermostat so Icalled whirlpool back and ordered my thermostat and received it in 2 days put the thermostat in put the back on the dryer and I was back in business didn't get behind waiting on my washing ,,not tomention we were in the process of moving thank you you'll worked with me .Iwould buy another whirlpool product easy to work on a and awesome customer service .

Dryer keeps running without drying

  • Customer: Charles from Summit MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched installation video (very hepfull),used battery driver (faster)to remove back (9 screws). Used nutdriver to remove screw holding old part, removed part. Changer wires one at a time to prevent wrong placement of wire. Parts ordered were correct and arrived in 2-3 days. Thanks PartSelect. Very easy install, video made me an "instant repairman."

clothes not dry

  • Customer: ROBERT from CARMEL NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
followed the excellent video that showed how to replace the part

no heat

  • Customer: Roy from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I have replaced the element, the thermal cut off switch. high limit thermostat and thermal fuse. Still no heat.... I am trying to figure out what part next. I could use your help.Roy

Dryer would not start.

  • Customer: Sam from JOHNSON CITY TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took back panel off. Did not have a clue! Went to Partselect Web site,entered my problem,BAM! instant solution.Watched repair video and was surprised how simple repair looked.Heck I can do this,no problem! I work from 7 A.M. to 5 P.M. so theres no chance to stop by local appliance part store before they close. Ordered my parts from Partsselect,arrived in just two days. Followed video instructions ,completed job in thirty minutes or less! I also got important information regarding maintenance and cleaning dryer to prevent fire hazard.Thanks,for help and saving me time and money.When I have a problem in the future I now know where to go.

would not heat up enough

  • Customer: Carol from Minneola KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed troubleshoot & repair steps provided by partselect.

Dryer took a long time to dry clothes and towels,

  • Customer: Antony from Boone NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I viewed a number of vidieos on the Webb to determine the possible problems. The vidieos explained and demonstrated how to test the parts that could have been causing the problems. I tested the parts described in the vidieos and the ones I was able to test showed that they were not defective. I was unable to test the Cycling Thermostat and the High Limit Thermostat to my satisfaction so I ordered the two parts and installed them as demonstrated on the vidieos. The dryer works as if it was a new one. I am a very satisfied customer and will definitely purchase my parts from partselect.com in the future.

Belt & clip where both broken

  • Customer: Amy from Seagrove NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

drum not turning

  • Customer: Tony from Greenville IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a video on utube and realized how easy this looked, took my dryer apart to see the belt broken in half and the idler pulley in pieces. Found Partselect on the internet and ordered my parts. Partselect was awsome, website was easy to navigate, ordered my parts and they were at my house the very next day and were the correct parts. Cleaned all the lint and dust out of the inside of my machine, installed new parts and put it back together. Works great and is still running strong. A service call, plus parts (with thier mark up) could have easily been $150.00 - $200.00 dollars. this repair was complete in about an hour and only cost me $37.50

Broken belt and bent idler pulley

  • Customer: Mollie from Walterboro SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First unplug the unit. Take the lint filter out and remove the two Phillips-head screws at the edge of the opening. Then using the putty knife to unlatch the top panel of the dryer, insert it into the seam on the front about 3" from each side. When you feel the knife up-against the latch, apply a little inward pressure with the knife and pull up on the top panel. When you release both sides the panel, it will lift up and back against the wall(secure it so it doesn't fall forward while you are doing this repair). Looking down on the right-front corner you will find a connection for the door switch, Dis-connect it. Just below that connection, on the inside, is a 5/16" screw that holds the front panel on, take that one and another one just like it on the left side, out and the front will fall forward about an inch and then you will lift up on the panel while holding drum in place. Inspect the clips that hold the bottom of the panel on and be aware how the panel attaches to them. Try to keep the drum in place and set the front panel off to the side so you can easily grab it to put it back on. Looking under the drum remove the belt and idler pulley. The pulley is usually not in the position it should be in, it likes to fall over when it has no belt pressure on it. Hopefully you had already unpackaged the new belt and straightened it out. Loop the belt over the drum, rib side to the drum, and move it to where the old belt had been riding on the drum. Back under the drum, you should hold it in place with your shoulder, with idler pulley in hand-- install the idler pulley. There's probable a clean spot where the old one was and the humpback should point to the right side of the dryer. With right hand steadying the idler pulley, the left hand should pinch the belt together and feed it under the wheel and pull it out and hook it on the motor pulley. It may seem to be a tight fit but once its on you should be able grab the outside edge of the drum and slowly turn it without hearing any scraping noises. Double check that the belt isn't twisted. Before putting the front panel back on or if you had to take the drum out, make sure the felt seal on the back edge of the drum is not folded inward. the wheels that the drum roll on must be in the groove. Carefully reach to the back to check that they are in the groove of the drum. If everything seems to be in place, hold the drum with one hand and grab the front panel with other. Place the bottom of the panel against the unit and lift up about an inch and place the square holes at the bottom of the panel on the clips on the unit, it may take a couple of tries, then lean the panel forward making sure the drum goes around the felt seal on the panel. Once the panel is against the unit , install the two 5/16 screws securing the front panel to the unit. Turn the drum by hand to make sure drum was installed properly. Reconnect door switch. Lower top panel and push down to secure it. Install the two Phillips head screws at the edge of where the lint screen goes, install lent screen and plug the unit back into the wall socket.

Lould nosie from Drum Whells

  • Customer: FRANCIS from PHILADELPHIA PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

loud squealing when running

  • Customer: Michael from Easton MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video provided by PartSelect. It pretty much went exactly like the video said it would. I was pretty sure the belt or idler pully must be the culprit, but I didn't even know how to open the thing up until I saw your video. I would likely still be putting up with the squealing without that video. Now the dryer is nice and quiet. -Mike

broken dryer belt

  • Customer: gary from stem NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
take two phillips srews out of lint catch frame. next take a screw driver pry up front top part on dryer.lean back top out of way.take two screws out of top of dryer door. disconnect electrical connection dryer door frame.and pull frame upward and off. you will see roller bracket with end made to put in slott. put it in first slott under belt motor.take belt and pull it through under roller and hook it with screwdriver to motor pulley.by putting the tip of screwdriver on motor pulley with belt on screwdriver and lift up until belt slides on to pulley. make sure you put belt around barrel. before putting belt through roller bracket and on to motor pulley.and use something to put under barrel so it will not get in the way and fall off.

broken belt in our dryer

  • Customer: tom from mendocino CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the top and front off the dryer and had to route the new belt around the drum and through the pulleys, it was really easy and a heck of a lot cheaper then buying a new dryer

Belt broke

  • Customer: Edward from Barefoot Bay FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Called PartSelect, gave them the make and model number of the dryer and told them I needed a new belt for it. They gave me a price including shipment (under $20.00). I oreder the new belt and it arrived within a week. I also got an e-mail from PartSelect with a video showing how to replace the belt. This was very helpful. I was able to watch the video, take the dryer apart, replace the belt (after a few tries), and put the dryer back together. Problem solved! Thanks PartSelect.
All Instructions for the 11060232002
1,186-1,200 of 1,258