Models > 11060092991 > Instructions

11060092991 Kenmore Dryer - Instructions

All installation instructions for 11060092991 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060092991
391-405 of 420
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice tray was broken

  • Customer: mike from fitchburg MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Excessive Idler Pulley wear; very noisy

  • Customer: Tim from Greenville SC
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

The dryer woulden't start

  • Customer: Larry from Walla Walla WA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I read the instructions on the internet. It told me what to trouble shoot first. The switch on the door then the thermo fuse and after that the thermostat. The off on switch on the door checked ok but the thermo fuse didn't when I followed the instructions on the internet. The thermostat did check ok. When I installed the new thermo fuse the dryer started like always before. I was pretty proud of myself for saving a hundred dollars or more. Thank you for the hlpful instructions.Larry

No heat

  • Customer: James from Rochester NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video and was able to complete the repair with no issues.

Tumbler belt replacement.

  • Customer: Mizael from Corpus Christi TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I must say what really made this install/replacement easy is the YouTube video link that was included with the belt replacement part. Once I saw the video (which showed my exact model dryer) it was a piece of cake! There was some work involved but once I got all the screws removed and took the shell off, installing the belt was a cake walk after watching the video. Many thanks!

Loss of heat

  • Customer: Jonathan from Alton Bay NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the front lower cover to the unit, located the heater and removed that. I installed the new unit and closed everything back up.

No Heat

  • Customer: Joel from Richfield PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took bottom accesses panel off dryer (two screws). To the right was heating element housing. Three screws to remove inside. One at the bottom of houseing bracket (holds up heating element housing) which connects to dryer cabinet floor. One at top of bracket (connects to bottom of heating element housing). One on the left side where the elements wires connect (screw goes through housing then through element side arm). Once the three screws are removed disconnect wires and pull element stright towards you. Once everything was diasembled I took shopvac in side machine and swept it all out. Just reassble the same way you took apart.

Dryer stopped heating

  • Customer: Gina from St. Marys WV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband took the back off the dryer and the Thermostate fell apart in his hands. So detecting the problem was easy. Ordered a new thermostat it arrived in 2 days. Tok him 30 minutes to install and get dryer put back together. Works better than it had been.

moisture sensor stopped working

  • Customer: kim from cotati CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pretty easy to fix, hardest part was having to get the screws out of the inside of the dryer to replace the sensor itself. Once that was done it was pretty quick! PLUS super fast shipping on my part!! Was fixed before any repair places even called me back!!

The latch at top came off.

  • Customer: Tonya from Aberdeen MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It snapped right in. Works perfect.

wouldnt heat up

  • Customer: Autumn from Columbia IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
poped off front bottom panel just a couple screws to take loose slid out the heat element saved 172.00 dollers

the lint filter needed to be replaced

  • Customer: Kathleen M from McDonough GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the old filter out and placed the new one in the same spot.

Door keeps opening while clothes are drying

  • Customer: Patrick from Sanford NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

Dryer wouldn't start

  • Customer: Martine from Edgewood MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My experience was a positive one. I called the company and read the part number from kitchen aid and the technician on the other line knew exactly what i needed. He gave me the part number and the price and took care of my order. Within 3-5 days i received my part. I am really happy with this company and i will call again when one of my applicances is not working.

right part easy

  • Customer: JOHN from LAUREL MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
self...right part thank you
All Instructions for the 11060092991
391-405 of 420