11060092990 Kenmore Dryer - Instructions

Very simple. Using a Phillips medium size screw driver, I removed the broken lens. The new lens fit in exactly. Replaced screw from old lens. DONE

I purchased a new heating element installed and stil had same problem. I order the 2 sensor (kit) located in same area and that took care of problem. I should have purcahsed all at same time like someone else told us in the website. Thanks parts select for the very fast delivery

I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.

UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.

I checked all the thermostats with a OHM meter and found a bad sensor it was pretty simple using U tube as a guide and the parts were here in a day and a half I'm now getting ready to replace the transmission in my GE washer

I ordered kit to your recomendation, took machine appart as per your video (Very helpful), put machine back together only to find that that was not the problem.No other recomendation as to what else I should.

Tool of the back & cross brackets. I did not have to mass with electric panel. I did not have to remove the drum.

Just took the old one out and slipped the new one in! That's it! That easy. Thank you!

It was all put together... I just switched them!

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!

this belt is too thin for the capacity of this dryer.I had only removed the front panel,replaced the belt and immediately the dryer start.

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

Unplugged dryer from wall. Removed screws from the back using the socket set. Removed thermostat screws and disconnected wires(one at a time) while replacing new thermostat. Replaced second thermal and tightened screws. Replaced back panel on dryer. Plugged in, turned on and dryer was repaired..

Watched video on locating and testing parts (did help that I had a digital meter w/cont-tone ) removed and cleaned out dryer cabinet tested heating element-was ok went to thermal cutoff (tested bad ) ordered kit from part select parts arrived within two days (fantastic ) replaced parts in thermal cut off kit . Replaced dryer back also and important -removed dryer vent and cleaned out pipe -replaced vent pipe turned on the power tried dryer works like new again your easy to follow instructions made this a very easy job thanks people ! You saved me a great deal of aggravation and more important money