Models > 11042926200 > Instructions

11042926200 Kenmore Washer - Instructions

All installation instructions for 11042926200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11042926200
31-45 of 156
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer filling up with water when not in use

  • Customer: Dominick from Parker CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 8 people found this instruction helpful
Very simple repair:
- Turn off water and detach water supply hoses. (Good to have a bucket nearby to catch water left in hoses.)
- Remove 3 screws from the back of the lid; slide lid back 1" and lift off.
- Valve is mounted just under the lid on the back wall of the washer -- remove 1 screw from back of washer that holds valve assembly in place.
- Remove the 4 electrical connectors (2 black & 2 white) I numbered them with a sharpie so I wouldn't forget how to reattach them. :-)
- Use pliers to squeeze & slide the little hose clamp that holds the internal hose on the valve assembly. Once the clamp is out of the way, pull the hose off the valve assembly.
- Reverse the process to install the new valve assembly.

I ran into a little problem mounting the new valve assembly. The screw hole in the back of the washer did not line up with the mounting hole in the valve assembly. I had to drill a 3/16" hole just to the right of the original screw hole on the back of the washer. Used the new hole to mount the valve assembly, done.

Worn out hose had a hole it it.

  • Customer: Edward from Clinton MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 10 of 15 people found this instruction helpful
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

Two problems- Error code FH, Water filling drum when washer off

  • Customer: William from Longwood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 9 people found this instruction helpful
The Part Select website has some great information provided by customers. I search my error code problem that shut down the washer when filling and found the most likely scenario was a faulty flowmeter.
The other problem happening at the same time was the drum filling with water when the appliance was not in use. I thought the two problems were related, but upon further research decided that the most likely cause was a faulty water inlet valve.
I order the parts from Part Select and I could not believe how fast the shipping was. I just ordered regular ground but the parts got here in a couple of days.
The repair was easy. Remove four screws (need a star bit) from the top lid of the washer and remove the cover. The flowmeter and the water inlet valve sit right on top of the washer. Even with the lousy set of pliers I used, removing the clamps and disconnecting the hoses on both parts was easy off and easy back on. I had more trouble with the electrical leads on the water inlet, only because they were on so securely and I didn't want to rip out the wiring.
All together the repair for both parts took about 30 minutes.
Make sure you turn off the water supply and be ready to mop up a little excess water from the water supply lines when you disconnect them from the washer's water inlet valve.

Drum didn't turn/spin

  • Customer: john from chester NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 12 of 22 people found this instruction helpful
1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry

Washer would not spin ( F-02 comes on)

  • Customer: Steve from Dubuque IA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
1-Unplug washer
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remove 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.

Detergent leaking under Dispenser Drawer down front of Washer

  • Customer: Geof from Garner NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 17 of 37 people found this instruction helpful
Secondary problem was bleach being siphoned from dispenser prematurely when drawer slid in. Replaced Drawer, Detergent Container and Bleach Siphon parts. Appears to have been a change in the siphon design when compared to the original factory part. 5 loads completed since replacement of these parts with no premature siphon of bleach or leakage down the front of the washer.

Motor Control Board faulted.

  • Customer: Brent from Normandy Park WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 13 people found this instruction helpful
I read the instructions once and then started. It was easy but did take an hour to do the entire job.

the bellow leaked

  • Customer: Todd from Warsaw IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 11 people found this instruction helpful
make sure to take the front shield off... the job will go much smoother!...

FH code-4 minutes into cycle

  • Customer: robert from LITLE RIVER SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.

kept getting sud or f2 codes

  • Customer: carroll from Paxton MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
I had sears at my house twice to fix this problem.they told me it was a penny in the pump then when that didn't work they came back and said i was using to much soap which i wasn't.What they fail to tell you is that the high effiiciency washers use less water so they put a less powerful drain pump in so they get over worked and lose the ability to get the water out so buy a new pump and it will be like it's new again.

Not Draining - Flashing F-02

  • Customer: Andrew from Southampton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.

leak suddenly developed

  • Customer: Gerald from Troy NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 7 of 9 people found this instruction helpful
Somehow a bobby pin got into the drain pump housing. When it started to drain, the pin was rammed through the housing.Extremely easy to remove and replace. No special skills needed. Whirlpool did a good job in making it idiot proof. Unpacking the part took longer than installing it. Don't be afraid to do this repair. If you own a pair of pliers and a screwdriver,you can do it.

door latch error code

  • Customer: Gary from Sonoma CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

Washing Machine Filled with Water When Off

  • Customer: James from Naperville IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Turned off the water and unplugged the machine

Took off the top of the washing machine by removing three screws along the back side

Removed the hoses connected to the water inlet valve

Removed the hose coming out of the water inlet valve

Marked the 4 electrical connectors

Used plyers to pull the electrical connectors off. Needed to just pull hard. Won't break them off.

Remove the screw that connects the valve to the back of the appliance.

I confirmed this was the part causing the problem by blowing air through it with my mouth. I could tell that the hot water side was not closing all the way.

To replace the part, just repeat the steps above in reverse.

Washer would not drain.

  • Customer: Mike from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_
All Instructions for the 11042926200
31-45 of 156