took front panel off. Pump is right there easy to work on. Used pliers to take 2 hose clamps off. Used star screw driver to take 2 screws off of pump and removed old pump. The Assemblely goes the same way but the drain hose coming off the tube is not very easy to get back on. Hose is flimsey and the stem, on the end of the drain pump isnt long enough to keep hose on while tring to slide hose clamp back on.
Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.
Machine won't run. Door won't open. Makes buzzing sound
Removed top cover. Manually opened door through top cover opening. Removed 3 screws at front holding assembly. Removed 3 harnesses attached to assembly. Replaced with new assembly and screwed back in. Replaced harnesses. Certainly an easy DIY job.
washer would fill with water when it was not in use
Pulled washer away from wall, unplugged power from outlet, shut off water valves and removed hosed from back of machine. Removed the 3 screws on the back top of washer that holds top on and removed top. Unplugged the 4 wires on the back of the valve, removed the screw that holds the valve in place, pulled the valve out so I could remove the hose clamp and hose from the valve. I then reversed the operation. It is really pretty simple.
The product came on time and was perfectly rapped , it took me 15 mins to install after watching you tube videos on front loader washer . I was happy I didn't have to call a service man in . . . .
Very easy repair, once I read the reviews and watched a couple of you tube videos. I just released the band holding the gasket in place, pulled it back, unscrewed the latch and installed a new one. Less than a 10 min job. I am glad I found this web site, thanks guys!!
Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.
Used nut driver to remove 3 screws from rear of washer and remove washer top. Used Torx driver to remove single screw holding valve assembly in place. Loosened hose clamp with adjustable pliers and then unplugged 6 electrical plugs. Reversed process to put everything back together. Very simple.
1. Unplugged washer. 2. Turned off water supply valves. 3. Disconnected water supply hoses from back of washer. 4. Removed three (3) screws that secure top of washer from top/back of washer. 5. Removed top of washer. 6. Disconnected water outlet line from old inlet valve assembly by releasing clamp. 7. Labeled and disconnected spade connections from old inlet valve. 8. Removed single (1) screw securing old inlet valve in place and removed valve from washer. 9. Re-assembled using new inlet valve lickety split faster than a five-legged skunk.
I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished
I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again