11020932992 Kenmore Washer - Instructions

replaced water pump

I pulled up PartSelect, compared their advice with my problem, ordered a direct drive motor coupling for my particular model, received the delivery, and called a friend who's good at home repairs and who happens to be dating my sister. He was delighted to comply with our request (her clothes get laundered here) and he had no problem with either the repair itself or the part we ordered. Replaced the hoses, too. He said the new part had been improved over the old one, but everything fit together just like it should. Then I washed her work jeans. Success! I know this isn't what you're asking, but I was so pleased to have the correct part ready to go so he didn't have to mess around. It wouldn't have taken the afternoon, but I had to clean everything that had accumulated debris in 10 years of use as he went.

I was very happy the part arrived very fast and just what we needed, and service was super.. We took the old pump off slipped the new one into the slot and hooked the clips back on it and tighted it up and plug the washer back in and filled with water and it drained... We started doing laundry right away, and so far so good... Tired to leave a review but it won't let us into the site, but we would use the same company to order from again, thank you so much...

The repair video was great. I decided not to remove the outer cover as there is room to get to the pump if the washer is tipped back. The pump was easy to fix with the exception of the root cause of the failure. There was water getting to the pump shaft and over time it rusted and expanded in the pump housing causing it to split and leak. Once the old pump was removed, a file was needed to reshape the drive shaft to allow the new pump to be installed. Not bad on a 16 year old washer!

The Whirlpool website provided an excellent repair video, showing a step by step procedure for making this repair. I did have to clean the old parts but other than that i just followed the video. I used a socket to loosen a single bolt holding the agitator,I pulled it apart, replaced the cogs, and then put it back together.

Removed the agitator and the broken directional cogs. Ordered the new ones; recieved them within a couple of days. Replaced the cogs; in no time the washer was working like new.

I followed the video clip that showed how to make the repair that was attached to the email sent from Patrselect notifying me that my part had been shipped. The video clip was excellent and no other instructions needed. Thanks

Removed center top cap/sofetner dispenser. Removed center shaft bolt. Pulled off the top agitator section from bottom portion. Inside the upper agitator is the inner housing for the cogs, pushed right out. Remove cog retainer plastic ring. Careful, the cogs freely fall out and it a little tricky when reassembling. Reassemble every (cogs go in only one way), place the upper agitator back down and over lower portion in machine. Now Put the bolt back in place. Here's the tricky part. You will need a magnetic tip driver or socket to hold the bolt until you have it started because it sits in recessed "well" area. I used a dab of regular Elmer's glue from bolt head to socket. Worked like a charm. Be careful not to over tighten bolt. Remember, upper agitator should free spin one direction and "catch" in the apposing direction.

took motor of 2 screws instaled motor coupling

It was really easy, just follow the video. The washer machine sounds like new now.

After alot of helpful advise from you guys I replaced coupling water pump clutch, and the problem was still their. Then I tested motor capacitor and it appears dead. So I should receive new one tomorrow and hopefully success! I turned machine over and oil leak..so that's where the string with hose and air needle come in handy to put 90weight oil in through breather hole in gear case.

don't know, I ordered the part and my husband repaired it. Did not take him long at all.

Tipped the washer on its side and took the pump off then the motor then the coupling.

Pulled off the fabric softner holder, pulled out the cover for the agitator. Used a socket set to loosen the screw that holds in the agitator hub, pulled out the hub, removed the gasket from the cogs and replaced new cogs. Works like new!!!!

I purchased the part from PartSelect because it was very reasonable and it was OEM part. I have never replaced this kind of part on a washer so I figured it would take me a while. But PartSelect supplied a video showing the entire repair and that was the only reason I did not struggle with the repair. I will definitely buy any appliance parts I need in the future from PartSelect. Thanks Don