Models > 11016202691 > Instructions

11016202691 Kenmore Washer - Instructions

All installation instructions for 11016202691 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016202691
61-75 of 1097
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

improper or no hot water flow

  • Customer: Cynthia from Manchester MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 10 of 15 people found this instruction helpful
After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars instead of hundreds for a new machine.

water leaking from pump

  • Customer: michael from westmoreland city PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 12 people found this instruction helpful
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

Cold water flowed slowly

  • Customer: Timothy from Springfield VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 9 people found this instruction helpful
First, be sure to take the washer apart properly! The first time I fixed my washer I took it apart the hard way to change the clutch, and believe me it took longer to put it back together!
This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done!

Washmachine wouldn't spindry

  • Customer: Chuck from South Holland IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 8 of 10 people found this instruction helpful
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

leaking drain pump. Obviously a common problem with this washer

  • Customer: John from Solana Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 7 of 7 people found this instruction helpful
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.

Lid Switch broke off at screws

  • Customer: Dale from West Branch MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 7 people found this instruction helpful
First off it was much easier after watching the video that was on PartSelect website. It was a very good description of how to do the repair. The main thing is to have enough room to be able to move the washer around and be able to get around it.. Our washer and dryer are in our 1/2 bath so we had to completely unhook the dryer to move it out of the way to have room to work around the washer.. It was still a tight squeeze but it was pretty quick and easy once we got the area where the lid switch is attached. The only trouble we had was putting the front of the washer back on the tub correctly. That was mainly in part with not having enough room to move around. It was easy enough that is was worth saving the service call from the repairman. The most help was watching the video. Thanks PartSelect for your help.

Tub banged against the front of case during spin

  • Customer: Peter from Boca Raton FL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.

unbalanced load...knocking sound.

  • Customer: Edward from Easthampton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, screw). Reassembled washer then ran wash for a cycle. Successful fix.

water leaking during run cycle

  • Customer: michael from weymouth MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 7 of 9 people found this instruction helpful
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer

WILL NOT SPIN

  • Customer: Daniel from Temple TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 6 of 6 people found this instruction helpful
THIS IS A RELATIVELY NEW WASHER AND FAILED EARLY. MY PREVIOUS WHIRLPOOL WASHER LASTED 20 YEARS WITHOUT ANY REPAIRS.
1. FIRST INQUIRED ABOUT THE SPIN PROBLEM IN PARTSELECT. MACHINE WILL NOT SPING UNLESS MANUALY FORCED THEN IT WILL TAKE OFF BUT WEAK.
2.PARTSELECT SUGGESTED A CLUTCH PROBLEM. ORDERED THE PART THAT CAME FAST. WHEN I TRIED REMOVING THE SHAFT HUB WITH A HAMMER AND CHISEL IT WILL NOT GET LOOSE SO I OPTED ORDERING THE SPECIAL WRENCH TO LOOSEN THE TUB HUB.
3.I PUT THE MACHINE ON ITS BACK AND LOOSENED THE PUMP RETAINING CLIPS. DO NOT REMOVE THE HOSES FROM THE PUMP. MOVE THE PUMP AWAY FROM THE MOTOR SHAFT. REMOVE THE MOTOR ELECTRICAL CONNECTOR AND SET ASIDE.
4.REMOVE THE THREE BOLTS HOLDING THE GEARBOX-MOTOR ASSEMPLY AND PULL IT OUT OF THE TUB.
5.PUT THE ASSEMBLY ON A TOWELWITH SHAFT UP AND REMOVE THE SEPARATOR WASHER FROM THE OLD CLUTCH THAT IS SITTING ON THE GEARBOX. THEN REMOVE THE C-RETAINING CLIP FROM THE SHAFT.
6.PRY OUT THE WIRE RETAINING CLIP FROM THE CLUTCH AND PULL THE OLD CLUTCH OUT OF THE SHAFT.
7.THE CLUTCH KIT I ORDERED CAME WITH A PLASTIC BRAKE TO CLUTCH CAM SO I REPLACED IT TOO, JUST REMOVE THE RETAINIG CLIP FROM THE BRAKE THAT IS AT THE BOTTOM OF THE TUB AND REPLACED THE PART.
8.INSTALLED THE NEW CLUTCH AND THE RETAINING CLIPS IN REVERSE ORDER. REPLACE ALL PARTS THAT CAME WITH THE KIT. THE NEW CLUTCH SPRING WAS ALREADY IN PLACE.
9.PUT THE ASSEMBLY BACK INTO THE TUB AND RE-INSTALL ALL THE OTHER ITEMS IN THE SAME ORDER. IT SPINS GOOD NOW!
10.WHILE REPLACING PARTS, METHODICALLY CLEAN ALL THE LINT FROM THE MOTOR AND FROM UNDER THE MACHINE. THE GEARBOX SHOWED SIGNS OF LEAKING OIL SO ITS A QUESTION OF COST. I LEFT IT THERE UNTIL IT FAILS THEN I'LL BUY A NEW MACHINE.

No agitation, No spin, pump OK

  • Customer: Ernest from Midlothian VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 6 people found this instruction helpful
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.

  • Customer: Kevin from Disputanta VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 8 of 12 people found this instruction helpful
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

spin cycle was not working / poor

  • Customer: Craig from Plano TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 7 of 9 people found this instruction helpful
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

Crossed threaded plastic on old valve was leaking

  • Customer: David from Amity AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 10 people found this instruction helpful
Removed screws on top of machine to remove the control unit out of the way. Then used large regular screw driver to pry out the two clips that hold the back of the washer tight to the top frame. This allows the back to come away from the machine enough to get the water inlet valve free. Didn't have to remove the bolts at the bottom of the back of the machine (they were pretty rusty) Just removed the single screw holding the water inlet valve in place, slid it down and away from the back cover and could fish it out to the side and disconnect the hose (with plyers) and slide off electrical clips (make a note of which clip goes to which valve.) I removed the part first so I could make sure I was ordering the right one. When the part came (very promptly by the way) it went back together easy. Only question was regarding reinstalling the wires since I didn't mark which way they went. I knew which one went on the Hot and Cold but didn't know if it mattered which clips went on each terminal. Figuring it was AC guessed it didn't matter so put it together the way the connectors seemed to want to lie naturally. Put it together making sure no hoses or wires where pinched or rubbing against sharp edges. Replaced the rubber washers in the hoses and made sure the hose connectors turned freely (they had been rusted a bit and didn't turn on the hose freely and I think this was the start of the cross threading problem) This time the hoses went back on very easily, screwed them hand tight not forcing anything at any time (DIDN"T USE PLIERS!). Tried water and no more leaks. Washer filled faster also, think this was because the screens on the water valve were plugged. I'll have to remember to take the hoses off and make sure the screens are clear every couple years or so. If you are having slow fills, suggest you check this first before tearing in to the machine.
All Instructions for the 11016202691
61-75 of 1097