10652522101 Kenmore Refrigerator - Instructions

followed video instructions... only thing done differently was to tape crusher blades together before removing from shaft and added a drop of sewing machine oil to all screw sockets before replacing to reduce rusting and create greater ease of removal if further repairs needed

Really couldn't be easier. Loosen 3 screws that are easy to find. Disconnect the quick connect wiring harness. Now you have the old unit out. Take out the wire that tells if there is too much ice from the old unit and put it on the new one ( this was the hardest part of the project) Hook up the new wiring connector and hook it on the screws and tighten it up. Viola, your done. No messing with the water. Took me 5 minutes and I've never done it before.

TURN OFF WATER (if not already). Cut (or disconnect filler tube at bottom). Remove faceplate from refrigerator ice/water dispenser area. Remove screw holding metal bracket that holds water tube at filler point. Held metal mounting bracelet and pulled old filler tube out. Fed new filler tube thru bottom (hole is located at bottom of left door at hinge). As tube came out at top, pulled length needed to mount to new mounting bracket. Remounted new bracket (with hose attached) with new screw. Reconnected tube at bottom water line connection. Turn on water.

I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

checked the close and open switch on front door first

I watched the installation video and did just like it said. It was pretty easy. My ice maker is working once again, and I'm pretty proud!

from the back of the freezer unscrewed the water feed to the feed tube. unscrewed the tube from the freezer and removed it. Ran hot water through the fill tube and then reinstalled the tube back into the freezer. Cycled the ice maker and the water started filling the icemaker. Did not use the water inlet valve that I ordered. Matter of fact.. I returned it. Always remember to check the fill tube and make sure it is not frozen.

Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

I watched a couple of videos on your website about how to install a couple of parts that could possibly be causing the problem. Then I went and took the cover off of the area where the ice and water dispenser are in the door. I could tell from watching the videos which parts to look at to see where the problem might be. I figured out which part it was because I could see where it was broken. I then ordered the part. After I received the part I watched the videos again and then did the repair. VOILA! It worked. I put everything back together and the water dispenser was working. I was so pleased that I didn't have to call a repair man and I actually fixed it myself! My husband was so glad too.

I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

The video provided excellent instructions on how to to this job. The hard part was removing the keeper ring so that the auger assembly could be separted from its housing.

Watched the online video and it looked just too simple.....so when I got the new unit I did not have to even change the wiring harness and I was totally surprised that the change could be so simple and easy! Trick is to follow the video instructions and DO NOT take out the two top screws but just loosen them enough to lift up the old unit and remove it! Cannot believe it could be that simple and easy.

I removed the old water inlet valve and replaced it with a new one. I had to cut the existing water lines with a razor to fit the new design of the new inlet valve. I also had to remove the inlet water valve and attach it to the new one. It was real easy once I reviewed the U tube video on how to replace the valve.

Very simple repair. Followed the video instructions. Simply removed a few screws and nuthead screws. Removed the cover plates. Removed the old thermostat switch. Removed the plastics tubing over the temp sensor probe. Put the plastic tubing on the new sensor probe, ( rubbing a slight amount of vegetable oil on the probe to allow the tube to slide on easier,). Reinstalled the temp probe. Reinstalled the new switch. Connected the wires to the switch. Reinstalled the cover plates and screws. And the job was complete. Almost took me longer to write this out, than it did to complete the project. Hey, it was an easy fix.

Insert lenses from left to right snap in