Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10652522101

10652522101 Kenmore Refrigerator - Overview

Get Parts and Repair Help for 10652522101

If you know the refrigerator repair part you need, you can browse the list of all parts on the 10652522101, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 10652522101 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$5.48

Lower Door Closing Cam

The lower door closing cam is designed for use with refrigerators. It can be used on either the fresh food side, or the freezer side. It helps raise the door into position so the door can seal properly when closed. It also allows the door to easily swing open and closed. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace a door closing cam. To successfully install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. This replacement part is sold individually.

$57.42

Meat Pan with Handle

This clear convertible meat drawer can be used to store meats or vegetables. It has its own cold air duct to allow cold air from the freezer to flow into the drawer. You could have...

$70.75

Water Inlet Valve

Note: This valve has been updated by the manufacturer and NO longer includes the removable pre-filter bracket connector. Must be ordered separately part number WPW10445062.

$4.73

Door Cam - Black

The lower door cam is also known as the closing cam or door closer cam and can be found on your refrigerator or freezer door. The purpose of the lower door cam is to lift the door ...

$13.30

Control Bracket

This is a control bracket for your refrigerator, and may also be known as the dispenser control bracket. The function of this part is to be used as a fastener to hold the micro switches and the light socket in the freezer dispenser section in place. Its measurements are roughly 9 inches long and 5 inches high, and this model comes in white. The tools you will need in order to make this installation include a Phillips screw driver, a quarter-inch nut-driver, and a pair of needle-nose pliers. If your ice dispenser is not working properly, your bracket could be the problem.

$120.88

Replacement Ice Maker

The ice maker ensures your refrigerator generates and dispenses ice. There may be an issue with yours if it leaks water, generates too much or too little ice, or dispenses too much...

$8.84

Ice Guide

This is a refrigerator ice guide that is made entirely of clear plastic. This ice guide is located in the freezer door. Turn your refrigerator ice dispenser off before replacing the part. This is a simple repair, and the only tool you will need is a small flat blade screwdriver to push on the pivot tab on the bottom of the ice guide. Do not worry about breaking side or pivot tabs on your existing ice guide because it will be discarded anyway. This is a genuine manufacturer replacement part.

$23.78

Bi-Metal Defrost Thermostat

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function o...

$65.25

Icemaker Control Assembly

The icemaker control assembly is located in the freezer section of your refrigerator. It is what controls the icemaker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions, such as the heater, the water inlet valve, the cube size, and cube ejection. This replacement includes the control module and the motor, the motor is not sold separately. There are a number of reasons you might need to replace this part: if the motor is faulty, if any of the gears are worn out, or any of the plastic pieces are broken or damaged. If your icemaker is not functioning properly, you should start by testing this module. Before you begin repairing your refrigerator, make sure it is unplugged.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

was not making ice

  • Customer: GLENN from ORLAND PARK, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 623 of 682 people found this instruction helpful
take out ice bucket, just loosen the top 2 screws, remove the bottom screw, slide ice maker up & out, srewdriver to release wiring harness clip, reverse to put back in. was very simple. did not install water inlet kit yet. water under fridge stopped after i changed the ice maker. read more

Ice Maker quit working, I could manually cycle unit but then the water would overflow when unit was re-filling.

  • Customer: Max from Green Castle, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 562 of 580 people found this instruction helpful
I backed out the 2 top screws about a quarter inch and then removed bottem screw with a quater inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection with a small screwdriver. The new Ice Maker was wired correctley for my refrigeator so all I had to do wea reconnect the power connection and... read more

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 511 of 599 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more