10652284200 Kenmore Refrigerator - Instructions

Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.

If you follow the video to the letter it's a piece of cake

Unscrewed water inlet support bracket,placed new inlet valve next to old valve with same orientation.one by one disconnected water lines and power leads and reconnected to same position on new valve.Reattached bracket and job done..Access to valve very easy.

After figuring out online what I needed I was sent the step by step video on what to do. I have never did anything like this but I learned. In the Past my husband would deal with it but he is no longer alive to do this kind of stuff. Thank goodness you sent the video along with all the instructions as i had my laptop on the table and followed stopped it and followed it again. I actually did this . I am so proud of myself.Thank you for making it so easy.

The Sears man came out and told me it was the thermostat that needed to be replaced and it would cost $321 plus tax. I went on youtube and watched the Partselect video several times and decided to order the part after seeing how easy it was to install. Total cost $65. I put the laptop on the counter and watched it as I installed it. It helped that I could go back and watch a certain part if there was a problem. But I had no problems and installed it in 20 minutes. Very, very simple to do. Of course I had to pay $75 to the Sears man but I saved about $200 . Thanks Partselect.

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

The hardest part was figuring out how to get the front panel escutcheon panel off. With the putty knife under the bottom flange, you need to push down with some effort on the part of the flange where the drip pan slides in and twist the putty knife to disengage the locking tab. Once the panel is off, the rest of the job is easy with the aid of your video. Everything works like new...thanks.

Removed broken shelf and snapped in new one

remove power. Remove rear cardboard panel.. Remove wiring from startup kit. Remove defective startupup kit. Then reverse procedure.

Removed old valve. New valve does not provide for filter without modification. oOld valve used compression nut which had to be removed. Smooth cut with utility knife and push in. Needed a 1/4 inch compression coupling to hok up ice maker connection to 1/4 inch plastic hose fro the valve.

I watched the video a few times and pretty much did as it said to do. Took about 20 minutes start to finish. It seems to be working 100%.

I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

I took ice bin apart to ensure what part I needed. Got Serial # & Model # from inside fridge. Online search for Whirlpool Parts to check out prices. Settled on PartSelect for best price. Quick service too!!! Before putting it all back together, I reviewed the video. It was pretty good. Just left it up & after each couple of steps, I'd look at what was next. Went together with no problem. There could have been more details given, like ensuring that certain things lined up during reassembly. There was dead time when the narrator could have given pointers.

I removed the 3 screws but also removed the front screw of the left bin rail. This gave more room to maneuver I/M into position. The cover shown with the enclosed instructions does not show an Ice Plus (blower assy.). By removing the two mounting clips fron old unit and snapping on new one blower unit fits as original. Overall a very simple and quick repair. Note: None of the cables Inclosed were used as my harness does not unplug from wall. Thanks for the quick service PartsSelect.