10651512101 Kenmore Refrigerator - Instructions

First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.

Take off the old one and maounted the new one and get a lots of ice lol, thanks

My wife fixed the problem in about 5 mins. The hards part she said was getting them out of the shipping box. Thanks, a greatfull husband...

The glass cover came on time and in good packaging. I removed it from the packaging and slipped in to the shelf. It fit perfectly and was extremely easy to do. We are very pleased with the entire process. Thanks

After viewing video, took front cover off and found switch mounting broke. Ordered part through the online selector, which worked great. Received the part in a timely manner. Replace broken part, working great.

I took the ice maker right out

Bought a replacement ice maker from Parselect. I turned off the refrig. removed three screws. Unplugged the ice maker from the refrig. It was easy. Installation was the reverse of the removal.

removed the cracked bins and installed the new ones the biggest problem with this repair was making sure the bins were the right size it is hard to tell sometimes on the net

Replace complete Unit

Fan was barely rotating. So unplugged, removed back cover, removed fan and motor from frame work. Removed fan blade from motor shaft. Spun motor shaft which seemed fine. Pryed off back cover of motor to find a large but dry felt washer and a helical capillery slot formed into the motor shaft for carring oil from felt washer to the bearings. Added 30 wt motor oil and some 3in1 oil to felt and reassembled motor, fan and frame work. Plugged in power chord after getting rid of dust and dog hear on coils and is working like new.

At first I just ordered a new motor and followed the instructions on the video . The new motor started working overtime but no water was being delivered to the tray . Ordered a new tray and re-installed. Working fine now. At first the ice was sticking, but that seems to have stopped now. It may be better to pull the ice maker out and check to see if there is damage to the tray before ordering. That way it could save the time of not doing things twice.

Replaced control and motor on the basis that most respondents found this unit to be at fault when the icemaker failed. Unfortunately, this wasn't the problem. Sudsequently, I replaced the electrionic boards which did fix the system. It would have been helpful (and less expensive) if the patrsselect website provided more help with problem diagnosis. Otherwise, the website is great!

It was a very simple repair. The only frustration is that all I needed was a small plastic part on the motor assembly but had to buy the entire assembly. Glad that I found the assembly much cheaper on your site, but wish I could have just bought the small plastic part.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

watched video, followed the instructions and everything fell into place. since the wiring harness was not removable, I disconnected the harness from the the old unit and hooked it up to the new unit. put every thing back together,plugged in the power cord and turned on the water. water filled the ice maker and ice appeared in about an hour.