10651512101 Kenmore Refrigerator - Instructions

I watched the video and made sure my replacement ice maker matched the original. On my particular icemaker/refigerator combination, the electrical connection was slightly different than what was shown in the video, but the process for removal and replacement was very similar. I believe if more videos were available that were of the quality of the one on this website, there would be more people attempting to replace parts. I believe I saved over $200 by doing it myself. Kudos to the website and video people.

The repair was simple. Unplug the refrigerator, unplug the power connector from the fan and remove 3 screws. I removed the fan blade clip with the pliers and cleaned it off. Reversed the process, cleaned all the dust out with my shop vac and all works perfectly now. It took longer to pull the fridge out of it's normal position than to perform the repair. Every day it continues to work is one more day I don't spend $2000 or more on a replacement.

We were afraid of breaking the new part.But after watching the repair video about how much pressure to apply the part snapped right in. Thamk you for the video it helped alot.found the part quick and easy and it was shipped fast to us problem solved.

REMOVED three bolts holding the housing had a little trouble getting the housing out far enough to get the water lines back on that is when i had to use the needle nose.30 min at the most Thank You

Pull the ice maker out using a nutdriver Pull the use a srew driver to remove the srews did the same to replace it put it back in had ice in 20 min

After googling for a parts supplier, PartSelect.com came up. The site was well done and had the Parts List conveniently available. I watched the associated video which was the highest quality "how-to" repair video I have seen. As it turns out, though, the icemaker does not have to be removed from the freezer unit. I removed the icemaker's shutoff lever, removed 3 screws, pulled the motor assy off, slid the new motor assy in place and re-installed 3 screws. Reinstalled the shutoff lever per the video and JOB DONE.

First gasket received was damaged. Returned for full credit, no problem. Got second gasket and THEN found the real problem was the hinge! PartSelect accepted second gasket for full credit. No problem, no hassle. Awesome customer service. Thanks PartSelect!

This fridge is s ultraease 2 its 8 years old. Icemaker would'nt make ice. Its fairly easy all you do is take out the screws i recommend a power drill tho. Pop out the cover put the new motor in. I did'nt hear anyththing or see anything for a hour or two thought it did'nt work. Then i heard a clunk like ice falling into a bin. 3 hours later ice was falling frequently.

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

Drilled holes where pins had sheared off. Replaced pins with 4-40 x 1" screws and nuts and fastened switches and spacers on bracket. Used Loctite threadlocker to prevent nuts from loosening and installed bracket. So far, both ice and water dispensers are working fine.

My first try was to replace the water inlet valve. New valve was a good bit different than the original but not too hard to figure out. The main water inlet is on the inside rather than the outside. Flex hose and a stick in connector were included and I was able to work through that. But, when I turned it on the water still over flowed. The only thing left was the Ice maker. I ordered a new one. It came broken into several pieces. I ordered another, it arrived overnight with expediated shipping. install took maybe 15 minutes. problem solved. The company refunded me the full charge for the damaged ice maker and most of the charge for expediated shipping on the replacement. I'm happy and my wifes very happy.

I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you

Unplugged refrigerator and shut off water supply. My husband took out the ice cube tray, loosened 2 nuts (?) and took out 1 screw. Removed the old unit. Set in the new unit and tightened the two nuts and replaced the screw. That's it! (Parts arrived in 1 1/2 days!)

I watched the video on line and fixed as per the easy demonstration. Sad something 4 years old breaks.