10650584001 Kenmore Refrigerator - Instructions

The repair video indicated the removal of the entire ice maker when replacing the motor unit that I had ordered. Since I was replacing only the motor unit, located immediately to the front of the ice maker, made visible after removing the snap on cover, I chose not to remove the total unit and removed the old motor unit with the new one ordered and was successful with no further problems. I did turn the water off and disconnected the electrical plug of the fridge first. Three screws removed and replaced and done.

My ice machine stopped making ice I noticed the little dial under the cover stopped turning, so I bought the replacement part. It arrived three days later I un screwed the old one, and put the new in place and screwed it on the only little thing you might need to know is that the metal lever arm that moves up and down is attached to a plastic grommet with a two prong release that protrudes through the hole on the front of the assembly to release the old one just pinch them together. My ice machine works great now it was a very easy part to replace no need to call a repair service anyone with a screwdriver can replace this part

Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

There were excellent entries on the net of how to diagnose problem. Parts Select website had an excellent video on how to change part. Just followed instructions and changed parts in about 15 minutes. I am usually a klutz, but this was so easy

I had two repair problems. #1- Ice door kit & #2 control bracket. I followed the instructional video and completed repair in under 30 minutes. I surprised myself and had a happy wife.

The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

Removed outer cover. Removed control bracket which holds the water/ice dispenser paddles. Removed paddles from old/broken bracket, plastic pins were broken where the paddles hinge. Placed on new bracket placed screws and it was done. Very simple repair. Part cost less then $18.00 including shipping. Saved me mucho dollars!!!!

hardest part getting the putty knife in right place to pop off cover---found the plastic bracket was broken where the switch was held in place---- so ordered new switches and bracket ---- got the parts in 3 days--good service--easy job 2 do and saved lots of $$$$$$$$---

After determining the control boards weren't working (by the light was not working) I replaced the control boards. By the way I received the parts in only a day and a half.It only took about 15 mins. The parts came with a troubleshooting guide witch was a little difficult to understand, but I got through it. The new parts were working but still not making ice. The water line had frozen. My wife and I took a meat injector as a syringe and injected hot water in the line and a air compressor I have and blew air into it also. It works again. As a tip try to blow air into the water line with your mouth to see if its clear.

With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.

I watched your video and did just as he did. The video made it real easy and rather simple. It looked like it was going to be a mess until I watched the video.

Unplugged the refrigerator removed the cover and 3 screws. Pulled the old part off and replaced with the new and screwed it back on. Replaced the cover plugged it back in and it started working again.

I watched the short video at this website about replacing the bracket first. Then I replaced mine. Everything went smooth. No problems. Try it yourself.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.