10650569991 Kenmore Refrigerator - Instructions

checked the close and open switch on front door first

I watched the installation video and did just like it said. It was pretty easy. My ice maker is working once again, and I'm pretty proud!

from the back of the freezer unscrewed the water feed to the feed tube. unscrewed the tube from the freezer and removed it. Ran hot water through the fill tube and then reinstalled the tube back into the freezer. Cycled the ice maker and the water started filling the icemaker. Did not use the water inlet valve that I ordered. Matter of fact.. I returned it. Always remember to check the fill tube and make sure it is not frozen.

Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

I watched a couple of videos on your website about how to install a couple of parts that could possibly be causing the problem. Then I went and took the cover off of the area where the ice and water dispenser are in the door. I could tell from watching the videos which parts to look at to see where the problem might be. I figured out which part it was because I could see where it was broken. I then ordered the part. After I received the part I watched the videos again and then did the repair. VOILA! It worked. I put everything back together and the water dispenser was working. I was so pleased that I didn't have to call a repair man and I actually fixed it myself! My husband was so glad too.

I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

The video provided excellent instructions on how to to this job. The hard part was removing the keeper ring so that the auger assembly could be separted from its housing.

Watched the online video and it looked just too simple.....so when I got the new unit I did not have to even change the wiring harness and I was totally surprised that the change could be so simple and easy! Trick is to follow the video instructions and DO NOT take out the two top screws but just loosen them enough to lift up the old unit and remove it! Cannot believe it could be that simple and easy.

I removed the old water inlet valve and replaced it with a new one. I had to cut the existing water lines with a razor to fit the new design of the new inlet valve. I also had to remove the inlet water valve and attach it to the new one. It was real easy once I reviewed the U tube video on how to replace the valve.

Very simple repair. Followed the video instructions. Simply removed a few screws and nuthead screws. Removed the cover plates. Removed the old thermostat switch. Removed the plastics tubing over the temp sensor probe. Put the plastic tubing on the new sensor probe, ( rubbing a slight amount of vegetable oil on the probe to allow the tube to slide on easier,). Reinstalled the temp probe. Reinstalled the new switch. Connected the wires to the switch. Reinstalled the cover plates and screws. And the job was complete. Almost took me longer to write this out, than it did to complete the project. Hey, it was an easy fix.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

Removed the cover from Thermostate, removed the wires, and screws holding old thermostate, reversed instulation with the new thermostat, pretty simple.

First, watched video on Part Select Website. Very good. Pulled Appliance out from wall, Pulled the power plug, and removed the back shield covering the working parts of the unit. Found the fan and it was almost the same setup as on the video except that I could not get to one of the screws holding the motor in place so had to remove the entire bracket with the fan. Not too hard. Cleaned away dust and gunk around the site and noticed that the fan pulled air through a tunnel-like condenser coil that was packed with gunky lint...this is what probably killed the motor. I cleaned out the tunnel with the bottle brushes and vacuum and installed the new motor / bracket assembly. Then replaced the shielding around the fan and the back cover .panel. This is important because these form the channel that guides air flow throughout the condenser coils. This particular refrigerator has a barrier underneath which guides air flow from the front left to the condenser, through the fan, over the evaporator drip pan and out the right front. I cleaned all the lint and gunk from this area as well. I also made an air filter (cut from a furnace filter) and wedged it in front of the air entry section. This should keep the condenser coil cleaner over time but you have to remember to change the filter once a year. Probably should clean the condenser coil every 5 years as well. This unit has been very reliable over 20 years and may well go for another 20. Good luck with your repair.

I removed the top door hinge cover, removed the top hinge, pulled the refrigerator door off, layed it on the floor, removed the door cams, installed the new door cams, replaced the doo and top hinge and hinge cover. If you have this problem with your refrigerator door, be sure to replace the upper and lower cam.

Followed instructions- removed and replaced with new water inlet valve also replaced control bracket. Now no leaks and plenty of ice thanks to partselect, the right part, the right price and fast delivery . Thank you