10650552000 Kenmore Refrigerator - Instructions

I removed the 3 screws but also removed the front screw of the left bin rail. This gave more room to maneuver I/M into position. The cover shown with the enclosed instructions does not show an Ice Plus (blower assy.). By removing the two mounting clips fron old unit and snapping on new one blower unit fits as original. Overall a very simple and quick repair. Note: None of the cables Inclosed were used as my harness does not unplug from wall. Thanks for the quick service PartsSelect.

I checked to see if the compressor was running and it was not. I check the defrost fan and the compressor fan and they both were running. All lights were on inside the refrigerator. I then checked the compressor connection and using the multimeter I check for voltage on the two wires going to the compressor and I had 120VAC on the terminals. I then removed the start relay off the compressor as well as the overload relay. I then check the OHMS reading on the compressor terminals and I had good readings. I shook the relay and it was rattling. At this point I search on the internet for the start relay and ordered the parts. Received the part in two working days. Replaced the components and bingo everything started working. It took me more time to troubleshoot the problem than it took to replace the parts. Vernon

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

watched the installation video twice and took my time to make sure all parts were put back together in the right order

Moved fridge out from wall, unplugged power cord. Laid on floor, removed 6 screws from cover. Removed one threaded bolt to allow assembly to slide out. Removed special nut, and took fan off. Removed 3 motor mounting bolts. Unscrewed 2 wire nuts, and untwisted wires. (option 1, no ground) Vacuumed entire area around motor. Used 3 bolts to mount motor to holder assembly, and special nut to install fan. Stripped wires back about 3/4 inch. Twisted two wires together CW, and installed new wire nuts. Slid motor assembly back into slot,(keep wires away from blades) and used one threaded bolt to secure assembly. Reinstalled cover plate with 6 screws. Plugged power cord in to test air flow (out through cover vents). Moved fridge back into place. The loud whirring noise did not stop for a day; then quiet!

I followed the really great repair video on this site. I would not have been able to do it without the video. Thanks very much for the video. Once I had the front panel off, it was relatively easy. Definitely would buy here again and attempt repairs myself. Very good experience! Very happy.

When very smoothly, as the video outlined the procedure.

I watched a video several time to get the steps in the removal and reinstall. It really was not that hard but first time repairs can take extra time.

turned off power unscrewed all the screw that mount ice maker, used flat head to release the clip on the wire harness, took out and exchanged the overfill wire, plugged the new unit in at wire harness, lined up and leveled ice maker tighten all the mounting screws, very simple repair i am very happy that you still had the orginal (OEM) ice maker, thanks Herb

Watched Video - took you through step by step

was really ease remove three scwes fron back panel plus two more screws from the water valve

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

with a mirror to see the small hole on the front side of the icemaker.... very simple, took 1 minute

Removed three screws. Removed old part. Inserted new part and reinstalled three screws. Doesn't get much easier that

It was this simple. I removed the old drawer and slid the new one in place. I was simply amazed at how quickly I received the part. I ordered it on the 24th of July and received it on the26th.