10650534100 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Solid ice on Evaporator coil
With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back
Parts Used:
-
PRAKASH from PISCATAWAY, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker would go through a complete cycle, but wouldn't put water in the tray.
We changed the valves first to try it and then we changed the ice maker. That worked. Thank you nephew for helping me.
Parts Used:
-
Carolyn M from Riviera, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Dryer was constantly running and not getting hot
Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.
Parts Used:
-
HENRY from WARMSPRINGS, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Just a bit tight getting to some wires
I watched your video and did just as he did. The video made it real easy and rather simple. It looked like it was going to be a mess until I watched the video.
Parts Used:
-
Mike from Spokane, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Not making Ice
Unplugged the refrigerator removed the cover and 3 screws. Pulled the old part off and replaced with the new and screwed it back on. Replaced the cover plugged it back in and it started working again.
Parts Used:
-
John from Munford, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Freezer not cooling. Temperature rising.
One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.
Parts Used:
-
Jeff from Austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door water dispenser broken
Removed outer cover. Removed control bracket which holds the water/ice dispenser paddles. Removed paddles from old/broken bracket, plastic pins were broken where the paddles hinge. Placed on new bracket placed screws and it was done. Very simple repair. Part cost less then $18.00 including shipping. Saved me mucho dollars!!!!
Parts Used:
-
matthew from fresno, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no water but icemaker would dispense
hardest part getting the putty knife in right place to pop off cover---found the plastic bracket was broken where the switch was held in place---- so ordered new switches and bracket ---- got the parts in 3 days--good service--easy job 2 do and saved lots of $$$$$$$$---
Parts Used:
-
conley from Melbourne, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Leaking ice maker
The ice maker installation video was a life saver. Thank you. Followed video instructions and removal of old unit and installation of new unit took almost no time. Again thank you for the excellent video.
Parts Used:
-
Arthur from Tustin, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Icemaker quit working
Watched the video on the Partsselect how to remove and install the icemaker. It made the job real easy to do. It took about 20 minutes to exchange it out. It took me about a extra 30 minutes to remove the water line to the icemaker and install a in-line filter. The water froz up where it pours into the icemaker. Ran some hot water through the line, reinstalled the line and everything works great now for over a week. Just a extra tip always check the water line to make sure Its clear. George Fontana CA
Parts Used:
-
George from Fontana, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Refrigerator would not run
Watched your installation how to video. Applied same procedure. Went smoothly.
Parts Used:
-
Rodney from Rockdale, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced Ice Bin Auger Drum
Followed the DYI Video provided by partselect. Best advice, take a digital pic prior to disasembly, which of course I didn't! My cordless screw driver w/o the tip, is the same size as the screws thus no need for a nut driver.
Parts Used:
-
DAVE from VANCLEAVE, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
No Ice Through Door
I had two repair problems. #1- Ice door kit & #2 control bracket. I followed the instructional video and completed repair in under 30 minutes. I surprised myself and had a happy wife.
Parts Used:
-
Joseph from Antioch, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker was leaking water
First I read your trouble shooting guide and determanded it was the ice maker. Then I watched your repair video which was very helpfull. I ordered the new icemaker, When it arrived I installed per video using only a 1/4 inch nut driver. IT was esay. New ice maker works great.Thank You for the information you have online and the parts and service.
Parts Used:
-
philip from oregon city, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
fill tube broken at elbow
Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!
Parts Used:
-
Jack from Houston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!