10650509991 Kenmore Refrigerator - Instructions

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

I just followed the enclosed instructions

Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!

Neither the OEM instructions nor any of the PartSelect videos explained BOTH ends of the tube for my particular appliance. All very thoroughly covered the obvious connection with the water valve from the wall. However, the push valve end for my KitchenAid is supposed to insert into the water filter chassis, which can barely be seen from the back of the appliance, much less reached with any tool. In order to make the repair, one must either remove the water filter chassis (which I attempted unsuccessfully), or put the appliance up on jacks in order to reach the push valve site.

I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.

My husband and I followed the instructional video on how to replace the "direct drive drum". We took note of how everything looked prior to dismantling the ice bin. We made sure we had the proper tools and a large flat surface to work on and started taking out the screws. Replaced the new drive drum part and put it all back together. The whole process took approximately 30 minutes and the ice crusher works great now. I'm a happy camper!!

I was surprised to find that the only part regulating the temperature in the refrigerator was a part called an "air diffuser". This consists of only an actuator that opens slots to let cold air come from the freezer. It is connected to a thermocouple. That's it, no fan, no motor, no other mechanical parts. So it was no surprise that, since the freezer was working well, the only solution as to why the refrigerator wasn't working (besides the doors sealing normally) would be to replace this part. You can use a mirror to "see" if the small door slits are actuating when the refrigerator is calling for "cold" from the freezer. The slits may look like they're not open all the way and believe me, if they aren't open ALL the way the fridge won't cool down properly. I took the old diffuser off and left the hole open and the fridge cooled down better even without all of the ductwork directing cool air to the fridge section. Then you know for sure it's the part to replace. Get a thermometer to check it out. It's fairly easy, but the freezer ductwork needs to be removed in addition to taking the covers off the installed diffuser. There are tabs on the diffuser going into the freezer that hold it in place, only accessible behind the freezer ductwork covers. It was a little difficult to push the new diffuser tabs into place, just push hard on each corner. And there's a small ductwork part that fits inside the diffuser on the freezer side, make a note of how it fits in the old diffuser when you disassemble it, it will fit back into the new one with a little wiggling. Other than finagling the ductwork and shelving out of the way it's quick and easy fix. The fridge works great again!

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

I watched the ice maker installation video and I installed the new ice maker with no problem and was done in less the 30 min. with everything. The ice maker is working great. thank you Fred

Ordered part over the phone and received it two days later.....excellent service

Door cams were worn out. Removed food from door. Removed top hinge cover and hinge. Lifted door off lower hinge pin and placed door on a table. Removed old door cam and installed new one. Replaced closing cam on lower hinge. Set door back on lower hinge and closed door (magnetic strips hold the door in place). Reinstalled top hinge and replaced cover.

I receved the new ice maker and the only problem I had was getting the old ice maker plug disconected from the frig.