Models > 10644033603 > Instructions

10644033603 Kenmore Refrigerator - Instructions

All installation instructions for 10644033603 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644033603
556-570 of 651
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No problem

  • Customer: Ordean from Minot ND
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
The repair went just fine. Your instruction regarding using the wiring harness were clear. Most of all I am happy to not have to listen to a noisy motor all night.

Condenser fan made loud noise.

  • Customer: Robert from Perrysburg OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video that was attached to my order confirmation (great idea) and just followed it step by step. Real easy repair since I had tried to fix the noise first without ordering parts, so I knew what I was doing Did a temporary fix which quieted it down while I waited for the parts and then the repair itself was pretty straight forward.

rocker switch broke off

  • Customer: STANLEY from OAKLAND NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Condenser Fan quite

  • Customer: Jennifer from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I tried WD40, it worked for a day. Got a new part from PartSelect.com and was a good brand. Panasonic. Easy fix and works great. Saved a bundle. I priced a new fridge, no way, this was better. Thank you Partselect.

Ice Maker Not Making Ice

  • Customer: Gail E. from Palm Harbor FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The part arrived very quickly. I set up the laptop computer on the counter and started the instruction video (THEY ARE THE BEST!). With just a few starts and stops of the video during the installation in less than 15 minutes the repair was complete! The next day I had more ice than I needed. What a fabulous way to make appliance repairs at minimal cost! I will ALWAYS use PartSelect for any future repairs. I should also tell you that a 70 year old Woman did this repair - easily! If I can do it so can you!!

Protective cover for bulb had melted

  • Customer: Lee from Brooklyn NY
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

No Ice

  • Customer: James M from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced Ice maker unit

The icemaker stopped working

  • Customer: Patrick from gilroy CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed icemaker and installed the new one. Went from six tiny ice cubes to four big ice cubes. Ice is of a higher quality, and the ice no longer falls out of the bin as the old ice maker's ice had once been prone to doing. A certified epic win on my part.

Water leaking and freezing on the botton of the icemaker mold

  • Customer: Richard from Jacksonville FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Install was done in reverse order of uninstall. The only thing that made this install a bit tricky is that the fill cup on the replacement icemaker was not the same part as on the original. I could have attempted to trim the replacement fill cup but didn't know how well that would work. I instead elected to install the original fill cup onto the new icemaker. This added a bit of time and complexity to the repair but I followed a repair video for when just the ice mold is being replaced. That video told me how to disassemble the ice mold and timer motor which had to be done to in order to replace the fill cup. It's been about 2 weeks since repair was made and the icemaker seems to be working properly.

Ice maker would not make ice

  • Customer: celene from Lavonia GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Completely disconnected the power. Just shutting off the ice maker switch does not shut off the power to these boards. The emitter and Receiver boards are located in the side panels of the freezer-one on the right and the other on the left. Just remove the 3 screws in each cover and disconnect the wire connectors and install the new boards. It's very straight forward and easy to do.

No ice, the cabinet was warm, but most annoying it broke every 6 mos since I got it

  • Customer: Cynthia from Wilmington DE
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

Failed to make ice

  • Customer: Billy from Horseshoe Bay TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your repair video was spot on. Should have watched it before I removed the old defective part. Would recommend it for anyone with same problem. I'll call on you again. Thank you. Billy

Replace ice maker

  • Customer: Alfred from Jackson NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Remove the door on the icemaker. Remove a screw on the bottom right of the icemaker and remove the bracket. push two small tabs on the bottom to release icemaker and slide out. unclip plugs that are on the wire. To reinstall just do the reverse.

Ice mold was leaking causing all the ice to freeze into one chunk.

  • Customer: Douglas from Spring TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

condenser fan would not come on, and when it did, made loud noise.

  • Customer: Sean from Simi valley AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.
All Instructions for the 10644033603
556-570 of 651