Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10644033603 > Instructions

10644033603 Kenmore Refrigerator - Instructions

All installation instructions for 10644033603 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644033603
526-540 of 651
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker quit working

  • Customer: Rudy from Tyrone, GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I tried to put in the model ice maker sent to me but it was not an exact match to the one I was replacing. The water fill cup on the upper right side was too tall to fit over the rubber fill hose so I had to take the old ice maker apart and swap it with the new cup. Then I installed the new maker but it did not work over night. I took it back out and disassembled it and saw condensation on the electric motor housing which had turned to ice. I figured that if there was ice on the outside then there was probably some on the inside as well. I used a hair dryer to evaporate the ice/moisture and then re-installed the unit. It has worked fine ever since. I do not think that I needed the entire ice maker unit but just the timer motor. I could have saved some money and time if I had known that the motor was available by it's self. The shipping was fast for the unit but look over the unit that you are replacing and make sure the picture of the new unit is IDENTICAL to it. Watch the video PartSelect offers and it will help you a lot.

The heat element went out.

  • Customer: Michael from Peachtree, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought I would have to have a serviceman replace the unit. After watching your video, I thought I would try it. It was much easier than I had imagined. If it wasn't for your video, I probably wouldn't have tried it. Thanks for your help. I will definitely check with your company first, for the next repair odyssey.

stoped making ice

  • Customer: Andrew from Bonner Springs, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
with video's help installation was not real difficult.

ice door would not seal warm air out & ice maker would freeze up.

  • Customer: Earl S. from Denison, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After reading (Warm air getting into freezer) by David from Chesterfield, MO & (Ice door was broken) by Ray from San Antonio, TX, it was easy to follow their instructions (especially- Patience is a virtue! and go step by step. Thanks to both for their detailed instructions, this retired mechanical engineer was able to 'get it done'. Stan from Denison, TX

Ice Maker Did Not Make Ice

  • Customer: Rodney from Sacramento, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed a total of 12 screws, unplugged the control boards, plugged-in the new control boards and replaced the 12 screws.The FAQs section of the PartSelect troubleshooting guide helped me correctly identify the control boards as the source of the problem. The LED sequence was the key to identifying the problem.

lcemaker stopped making ice.

  • Customer: Scott from McCall, ID
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We ordered the icemaker part and a water filter. The water filter slipped into the slot and was very easy to replace per instructions on the box. We put the video on how to replace the icemaker on the computer next to the refrigerator and followed it precisely pausing it between steps. After replacing the icemaker we thought it did not work but it took a few hours before it started making ice again. After waiting overnight we awoke to new ice in the bucket. It went smoothly and was a breeze to fix.

Installing new "wiper" at bottom of ice in-door ice dispenser

  • Customer: Peter J from Montgomery, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The plastic "wiper" attached to the bottom of the ice "auger" in the ice dispenser unit broke. (It was made from a plastic that was not up to the freezing temps and heavy ice loads it had to move.) The new unit seemed to be of a different type of nylon/plastic. Problem was that the small machine screw at the bottom of the auger assembly could not be removed because of corrosion. I had to drill it out. Choices then were to purchase a new auger for about 60 bucks or reassemble the unit with a new 6-32 machine screw. There will not be enough metal left to allow it to be tapped so simply clean it out well and glue in the new screw with JB Weld. Allow to cure over night and you're back in business. Ours works fine so far. Good luck!

The old condenser fan was rattling and driving everyone nutts.

  • Customer: William from Salem, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
I surfed partselect and read that a reader had a similar problem with a rattling fan. I then removed the back panel, after I had unplugged the unit, and was able to feel the slop in the fan shaft. I then watched the video of how to replace the fan and ordered the part soon after. The part arrived 3 days later! Easy to do. I was finished in 12 minutes and the fridge runs silently. The part of the job that took the longest was vaccuming the undercarriage. There was alot of dust! Couldn't have helped the efficiency on the fridge. Keep it clean.

no problem, just needed to change the filter

  • Customer: Ruth from Katy, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old one and installed the new one

Ice buildup on ice maker

  • Customer: Russell from Orlando, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

Ice Maker not working

  • Customer: Thomas from PALMYRA, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
There were excellent entries on the net of how to diagnose problem. Parts Select website had an excellent video on how to change part. Just followed instructions and changed parts in about 15 minutes. I am usually a klutz, but this was so easy

Water Filter Needed To Be Replaced.

  • Customer: D'Joane from Union City, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old water filter by simply twisting the the cap that houses it at the bottom of the refrigerator and replaced with new water filter. No fuss, no muss! Very impressed. Also, I was quite pleased to have received the water filter that was designed specifically for the whirlpool model that I own. I expected to receive some generic-type model based upon the reasonable price that I paid. Kudos to partselect!

The icemaker would occasionally dump the ice in the tray. I could unfrost the tray and then it would seem to work for a couple of times and then stop again.

  • Customer: Leonard from Las Cruces, NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old icemaker and tore it apart as much as I could to see if I could see anything obvious. I also took a resistance reading on the heating coil in the bottom of the icemaker. It was good. I then hooked the old icemaker back up with the end cover off. The plastic wheel on the end of the ice maker did not move. I then ordered a new ice maker, installed it and it has worked perfectly ever since.

Light switch which turns on the lights when the door opens went out

  • Customer: Dennis from Lawrenceville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

ice maker stopped making ice

  • Customer: stephen from chico, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After determining the control boards weren't working (by the light was not working) I replaced the control boards. By the way I received the parts in only a day and a half.It only took about 15 mins. The parts came with a troubleshooting guide witch was a little difficult to understand, but I got through it. The new parts were working but still not making ice. The water line had frozen. My wife and I took a meat injector as a syringe and injected hot water in the line and a air compressor I have and blew air into it also. It works again. As a tip try to blow air into the water line with your mouth to see if its clear.
All Instructions for the 10644033603
526-540 of 651