Models > 10644029600 > Instructions

10644029600 Kenmore Refrigerator - Instructions

All installation instructions for 10644029600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644029600
886-900 of 979
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker running over, water/ice fall in freezer

  • Customer: VICTOR from MARANA AZ
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Used hair dryer to melt ice so I could remove old ice maker. Used old icemaker Model #2198597 to order new ice maker. New ice maker water funnel that catches water that goes into the ice mode was higher then the older one. Everything else looked ok. I contacted parts select and was told, if I took the new icemaker apart and it didn't work I could not return it. After three phone calls I was told that I could keep the new ice maker and they would refund my money. So I was left with take the new ice maker apart or cut down the funnel. I cut down the funnel and slid the new ice maker into place. My second choice was to take the new ice maker apart & put on the old funnel. Parts select (Susan) has sent me an email that I would get my money back as the part was not correct. I feel bad about this the way it worked out. It took me about 20 minutes to cut the 1/2 inch off the new funnel.

Ice maker not working

  • Customer: Mercedes from Lyndhurst NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We replaced the ice maker with the help of the video, it was very helpful and it is working fine, thank you very much.

Ice maker stopped working

  • Customer: Kevin from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After viewing the very clear video. Remove the ice maker door by first lifting the door and pressing in on the hinges. Remove the screw in the back lower right of ice maker with a one quarter inch nut driver and lift out the cover to expose the wiring harness. Pull the ice maker unit forward and out and reach behind it to pull out the wiring harness plug. The plug only comes out if you depress the small "push clip" in the center of the harness plug. Turn the old ice maker unit upside down and remove the three screws again with the one quarter inch nut driver to lift off the plastic cover. The wiring harness plug need to be pushed through the plastic housing to remove the plastic cover completely. Reinstall the plastic cover on the new ice maker. Reverse the procedure and install the new ice maker. This is really a simple repair if you watch the video.

Water would come through the door, but would not make any ice

  • Customer: Chad from Marrero LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the (3) screws on the bottom of the ice maker & the (1) screw on the electrical cover plate. I unplugged the ice maker & completely removed it from the freezer. Make sure to pay attention to the locking tabs or your maker will not come out. I took the bottom plate off the old ice maker & attached it to the new one, slid it in & re-plugged it. Tighten all screws back where they are to go & now I have ice. It was a breeze to do this job. Part was completely as described.

Failed to make ice

  • Customer: Billy from Horseshoe Bay TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your repair video was spot on. Should have watched it before I removed the old defective part. Would recommend it for anyone with same problem. I'll call on you again. Thank you. Billy

Kit did not match up to existing bracket

  • Customer: John from Severna Park MD
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

Ice maker was missing / broke.

  • Customer: Chris from Norwalk IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the quick video once to see the type, if it matched mine, and the difficulty. I went ahead and ordered the part and within minutes, I had the ice maker installed. The video was so well designed, I only had to watch it once!

Ice maker quit making ice

  • Customer: Charles from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
A local appliance parts distributor suggested that I go on line to get help figuring out the problem. The motor assembly was 51% probability. I ordered the part and followed the instructions given at the time of purchase. In a very short time ice was dropping.

plastic gear in ice maker was broken

  • Customer: Chieu from Suwanee GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Just watch video from part select and following the instruction to replace the control and motor assembly.

Ice Maker stopped making ice. A clicking sound was coming out of the unit.

  • Customer: Richard from Tomball TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the ice maker unit completely from the freezer, following a Utube repair video that I found. I originally thought it was just the control board that was defective, because on examination, found a burned-out copper trace on the board, as well as a burned-out plastic connection point. Installing the new parts was a breeze. This icemaker is pretty foolproof, with plastic tabs that line up with the housing. a matter of lining up the screw holes was all that was necessary. Only problem I had was attaching a plastic cover that shields the electrical connection from the water. Once all was installed, I had to wait overnight for the icemaker to make ice. We've had ice ever since! Thank you Partsselect for very courteous and fast service!

Icemaker stopped making ice

  • Customer: Jason from Houston TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Checked the hose above the icemaker to see if water was frozen. Ran the freezer at a lower temp to see if lines would unfreeze. Took a wild guess that a component was broken in the icemaker, but it was cheaper to get the entire assembly anyways. Removed about 4 screws under icemaker, disconnected icemaker, jiggled and slid the icemaker and tray out, traded out icemaker assemblies, and put it all back, probably took 10-15 mins, and it made ice again!

Wasn't making ice.

  • Customer: Carol from Brooklyn NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered both icemaker motor assembly and the emitter and receiver (sensors)as I was uncertain as to which was the culprit. We couldn't unplug the frige as it is heavy, so we shut the circuit breaker until we were done with the repair. The icemaker motor was a bit clumsy to remove. My refrigerator was entirely different than the one on the video I viewed, as I have a side by side and the video was of an entirely different model. The video's icemaker was not as clumsy to work with. My husband was a little apprehensive so I rode shot gun and assisted and he did great. He did change the motor first and probably should have waited to see if it worked. He didn't wait, and went ahead and changed the sensors....that was a breeze. We waited about 2 hours and lo and behold once the freezer went down to 14 degrees, the icemaker began it's magic and we had a full supply of ice within 24 hours. So, I saved quite a bit of cash by purchasing the parts I needed at Parts Select and eliminated the repairman's expensive fee. Very happy with end results.

Icemaker stoped making ice.

  • Customer: Henry from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
There are two tabs that hold the icemaker to the rails it sits on. I use a small screwdriver and pushed the tabs up to release the tray and slid the Ice maker out. the cover over the control motor just pops right off. Then I removed three screws from the control motor pulled it off and put the new on, replaced the screws and put the cover back on and slid the icemaker back into the rails. I shut the freezer door and within the five minutes it took me to put my tools back in the garage, it was dumping ice. Very easy to fix. You do not need to remove the screws that hold the icemaker to the tray.

ice maker stopped making ice.

  • Customer: Rliot from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removedicemaker and unscrewed 3 screws hill ding motor assembly and control module to ice maker . nstalled new part and attached it with the 3screws. reinstalled ice maker and ice making cycle began almost immediately.

Ice stripper cracked.

  • Customer: Otis(Butch) from Danville VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove ice maker from refrigerator,remove damaged part,replace with new one.
All Instructions for the 10644029600
886-900 of 979