Models > 10644029600 > Instructions

10644029600 Kenmore Refrigerator - Instructions

All installation instructions for 10644029600 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644029600
916-930 of 979
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Would not produce and dump ice fast enough to use.

  • Customer: Roy from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Used the trouble shooting off of YouTube and after finding that the heater was not at the right resistance, ordered a new ice-maker and installed. Very simple and a lot cheaper than going through Sears.

No Ice

  • Customer: James M from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced Ice maker unit

NO ICE,NO WATER

  • Customer: JIM from MADISON SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
TURN ICE MAKER CONTROL OFF,HOLD UP FRONT COVER REMOVE TWO SCREWS, REMOVE COVER, REMOVE REAR SCREW ON THE BACK RIGHT SIDE, SLIDE UNIT PART WAY OUT, MAKE SURE FLIPPER ON LEFT IS OUT OF THE WAY, UNPLUG CONNECTOR ON RIGHT, REMOVE UNIT,REMOVE BOTTOM COVER & PUT ON NEW UNIT,INSTALL IN REVERSE ORDER, TURN ICE MAKER CONTROL ON, DONE

my ice maker quit working several montyhs ago

  • Customer: Olan from Plant City FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I went on line and found your web sight. There was a list of the parts by number and I clicked on the rilght one. It brought up a video for repairing it myself. It was so simple. I just followed your instructions and within an hour I had ice. It makes so much ice I'm going to have to give it away. No really its great.

ice maker no longer worked

  • Customer: John from Bulverde TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The unit came out easily but the wire harness connector just didn't want to disconnect. The ice cold plastic was very difficult to work with and I had to use a screw-driver edge to pry it up and apart.

Icemaker quit

  • Customer: JL from Colby KS
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the video, it was just a matter of pulling one screw, changing the icemaker and reinstalling the screw. Super simple and now we have ice!

ice maker was leaking and cubes getting stuck

  • Customer: bill from escondido CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Just as the video described except there was a rubber fill tube hanging down from the top of the freezer that made it a little more difficult to install the new icemaker(I just had to bend it up and hope it didnt break)

Not making ice

  • Customer: George from Orange Park FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch replacement video then went from there. It was a simple replacement. Icemaker working and wife is happy:)

stopped making ice

  • Customer: Marquis from Bridgeport TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the icemaker stopped making ice. The cubes would get jammed up and finally just stopped all together. Removal of the icemaker and installation of the new one was pretty easy. The only problem was getting the electrical plug undone from the old unit. We have a lot of calcium in our water and I guess it finally ate through and ice was forming under the unit. It was five years old so not bad really. All is good....quick delivery. Thanks.

The icemaker would occasionally dump the ice in the tray. I could unfrost the tray and then it would seem to work for a couple of times and then stop again.

  • Customer: Leonard from Las Cruces NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old icemaker and tore it apart as much as I could to see if I could see anything obvious. I also took a resistance reading on the heating coil in the bottom of the icemaker. It was good. I then hooked the old icemaker back up with the end cover off. The plastic wheel on the end of the ice maker did not move. I then ordered a new ice maker, installed it and it has worked perfectly ever since.

ice maker quit working

  • Customer: Rudy from Tyrone GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I tried to put in the model ice maker sent to me but it was not an exact match to the one I was replacing. The water fill cup on the upper right side was too tall to fit over the rubber fill hose so I had to take the old ice maker apart and swap it with the new cup. Then I installed the new maker but it did not work over night. I took it back out and disassembled it and saw condensation on the electric motor housing which had turned to ice. I figured that if there was ice on the outside then there was probably some on the inside as well. I used a hair dryer to evaporate the ice/moisture and then re-installed the unit. It has worked fine ever since. I do not think that I needed the entire ice maker unit but just the timer motor. I could have saved some money and time if I had known that the motor was available by it's self. The shipping was fast for the unit but look over the unit that you are replacing and make sure the picture of the new unit is IDENTICAL to it. Watch the video PartSelect offers and it will help you a lot.

stoped making ice

  • Customer: Andrew from Bonner Springs KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
with video's help installation was not real difficult.

The heat element went out.

  • Customer: Michael from Peachtree GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought I would have to have a serviceman replace the unit. After watching your video, I thought I would try it. It was much easier than I had imagined. If it wasn't for your video, I probably wouldn't have tried it. Thanks for your help. I will definitely check with your company first, for the next repair odyssey.

Was not making ice cubes

  • Customer: Arthur from Heath OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the easy to follow video instructions posted on the same web page I used to order the icemaker. I chose to order the complete icemaker rather than the motor assembly because based on price, ease of installation, and the chance something else could fail in the icemaker unit I preferred to order and install the complete assembly. PartSelect was a great web site to use to purchase appliance parts and get instructions. Didn't think companies did this any more. Great!

no ice

  • Customer: James from Lawrenceburg IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
watched video, moved all wifes crap in freezer, replaced. Done, maybe 15 minutes total.
All Instructions for the 10644029600
916-930 of 979