Models > 10641529500 > Instructions

10641529500 Kenmore Refrigerator - Instructions

All installation instructions for 10641529500 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641529500
1,006-1,020 of 1,127
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Outside door water shut off return part broken.

  • Customer: Jerome from Abingdon, MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used 1/4 inch nut driver with swivel to remove the part retaining screw. Held new part into place and installed the retaining screw. Challenge was not hitting the level and putting water on me and the floor during installation. Relatively easy installation as long as you have patients.

Ice dispensor door would not close, dripped water, frosted inside freezer

  • Customer: Gail from Palos Heights, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Google refrigerator Model #, found your site, saw parts diagram right away, clicked on part 'Ice Door Kit', noticed your video on how to do repair yourself, showed it to my husband, ordered part, and it arrived the next day. That was the hardest part of the whole repair. I have been without use of the ice dispenser for about 9 months - took 20 minutes from opening box to getting ice again and saved myself a whole lot of money. I am one happy camper!!!

Water dispensor leaking/Retainer clip bent

  • Customer: glen from Rancho Cucamonga, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I couldn't figure out if the front plate would come off so getting access to the screw to unscrew it was problematic at first. I don't have whatever tool you need to get at that angle so I used an Allen wrench with a 6.5 mm socket to unscrew the screw and replace the clip. After figuring that combination out it went really fast.

water arm not returning

  • Customer: Claude from Warrior, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed facial then the board replaced the lever retainer and reversed process very easy when part's are correct also shipping time fantastic good job 5 stars thank you

Ice dispenser door hinge inop

  • Customer: Robert from Emory, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

Ice maker would not disperse cubes through the door

  • Customer: Danny from Fulton, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Looked at drawing to see what sequence the parts went.

Install new flipper. Old one missing

  • Customer: Wells from Hereford, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Remove 3 phillips head screws with #2 phillips screwdriver. 2. Gently pull mounting bracket outward from freezer case. 3. Using fine needle nose pliers remove clip washer from lower end of flipper mounting rod. 4. Note position of flipper spring and pull mounting rod upward far enough to insert downward through new flipper and spring. 5. Install clip washer removed in step 2. Position assembly onto freezer cabinet and secure with screws removed in step 1.

Replace ice maker

  • Customer: Alfred from Jackson, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Remove the door on the icemaker. Remove a screw on the bottom right of the icemaker and remove the bracket. push two small tabs on the bottom to release icemaker and slide out. unclip plugs that are on the wire. To reinstall just do the reverse.

Flipper had cracked

  • Customer: John from Boynton Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I went exactly as the video claimed. I was almost too simple a repair.

broke when intalling ice unit

  • Customer: bobbi from chehalis, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
repair was not to bad. removed 3 screws, then unplug wire harness. The next thing i did was removed clip that holds pin. slid pin back enough to put new flipper in place. needs to go in front of spring.once in place slid pin back in and put clip holder back on. Then plug wire harness back in and 3 srews . done.

ICE maker door hinge replacement

  • Customer: Theresa from Eagle River, AK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed two hex head screws, installed new part with nut driver for two hex head screws , very easy. I broke the tab off the hinge for the ice maker door when I installed a new ice maker the week before.

tab broken off ice guide. discolored and nasty looking. Ice maker had quit working also.

  • Customer: Jack from Casa Grande, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
First we bought an icemaker from Parts Select. That repair went very easy. The old icemaker the plastic coating over the metal had started to come off. We replaced the icemaker and I waited but didn't hear it fill the ice tray I was worried then that it was a valve that was mentioned on the website. The next morning my Wife told me, we have ice I was very happy. Easy to replace the ice maker just have to unplug ours at the icemaker itself, loosen 2 bolts and it comes right out. We just purchased this house and later while we where cleaning the dispenser paddles discovered that the ICE GUIDE the bottom tab was broken off and it was badly discolored so we quickly placed a 2nd order for a new ice guide and thought as long as we where doing that pop out the ice dispenser grille and replace that. They ship quickly and prices seem reasonable. Thank you Parts Select.

Discolored tray

  • Customer: Blair from Argyle, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Got on your website and found our refrigs expanded layout and ordered the part. The removal and install was less than one minute Including the clean up.

water stain on dispenser grill

  • Customer: luis from Grapevine, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the water stain on the dispenser grille was unsightly even after cleaning with baking soda and vinegar, hence, we purchased a new one. popped the old one out and put new one in. have used parts select in the past and their pricing was very competitive if not better than over vendors.

cracked and dingy tray

  • Customer: joe from lake worth, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
unsnap old teay snap new one in very easy
All Instructions for the 10641529500
1,006-1,020 of 1,127