10641529500 Kenmore Refrigerator - Instructions

Approached the repair as described in the video. Removal went very well. On installation the plastic tabs on the slide track were too tight to push into lock position using only hands. Had to use a screw driver and small hammer to tap the slide track into locked position. I regret that I did not replace both tracks at the same time.

Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .

the water stain on the dispenser grille was unsightly even after cleaning with baking soda and vinegar, hence, we purchased a new one. popped the old one out and put new one in. have used parts select in the past and their pricing was very competitive if not better than over vendors.

Follow the video.

unsnap old teay snap new one in very easy

Turned off the water to the ice maker; disconnected the wiring harness to the ice maker; unscrewed it from the freezer (two screws). Unhooked the ice lever bar, opened up the motor assembly. Switch the motor out (two screws). Installed in reverse order.

If you are having this problem, read this. My refrigerator door would not stay closed. This was over a year and a half time period. I thought it was something complicated and told my wife to call a repairman. Thank goodness she does what she does best - not listening to me! I finally had enough and went online and googled my problem and found PartsSelect. PartSelect had a repair video showing how to fix the problem. If you are like me, I'm very cautious about purchasing from a website in which I'm not familiar. PartsSelect is a reputable site (I promise I do not work for them). My refrigerator is over 8 years old and they had the part I needed, a lower door cam, along with a video on how to install the part. This honestly took about 5-10 minutes to do and I did it without any help. I was so aggravated at myself for waiting so long at doing this!! I actually ordered 2 of these parts, just for the next time. You can do this.

Pulled out the icemaker. Switched out the Motor Assembly (so easy) and woke up the next morning with ice. Our ice dispenser wasn't working either. This repair inspired me to take the ice dispenser apart and I found that the lever arm wasn't touching the contact when pressed. We now have ice and a working ice despenser. Oh yeah--my wife was so impressed. The part came in on time and it was very very easy to replace.

Per the video, easy out & easy in.

Instructions were really clear and easy to follow. Hardest part of the job was moving the refrigerator away from wall after it was filled with holiday groceries.

Once we figured how to get front off, it was like a puzzle. One piece at a time. So thankful part has been improved and replaced. It works better than before, just wish would have done it sooner.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

Unpluged the refrigerator. Removed the cover on the control unit by inserting a screw driver under the metal clips. Removed the three screws frrom the front of the control unit. Pulled toward the back of the refrigerator on the metal loop which turns the icemaker on and off and it came loose where it goes into the control unit. Wiggled the unit and it came free. place the new unit in approximately the right position. Reached into the icemaker and moved the ice eject leavers so the shaft would enter the control unit with the flat side of the ejector in the right position. Gently pushed the control unit into its place and aligned the screw holes. Replaced the three screws. Inserted the wire shut off loop into the hole on the back of the control unit housing. Pluged in the electric. The ice maker worked.

I ordered the parts and recieved them in about 4 days. I was very pleased with the time between order and delivery. I watched the installation demo provided and it was as spot on. All I needed was a small hammer to tap the old slide loose and the new slide on.

Followed instructions on video on website. Very easy to do. Removed old part, put in new and it took all of 15-20 minutes. Had ice in approximately 1 hour.