10641512100 Kenmore Refrigerator - Instructions

Perfect fit. Slides smoothly. Arrived quickly. Thank you for a very easy web site.

My Whirlpool refrigerator frezzer was not defrosting and the refrigator was not cooling. I followed the symptom parts advise (Defrost Timer Kit and the Bimetl-Def)of P/S. I pulled out the refrigerator from it inclosure and unpluged it, (note the shelf supports, the thinner ones are on the left side) I remove the shelfs and their supports,I removed the interior back cover of the frezzer, using a hair dryer I melted the frozen ice from the frezzer coile. Once all the ice was melted away, I cut off the old BIMETL-DEF and attacth the new BIMETL-DEF making sure the color wires are match correctly and using electrical connection plugs and electric tape I reconnected the wires. (2) I followed the video instruction for replacing the Defrost Timer Kit I found it to be quite easy to follow. The most deficult part was trying to position my body to remove the screws. I used an old CREDIT CARD to remove the face of the Refrigerator control buttons in order to access the compartment which house the Defrost Timer kit. I removed the old Defrost time kit and replaced it with the new one (following the Video instruction). I replace the frezzer cover inserting the lower four screws then using an old Credit Card I forced the top end of the frezzer cover under its retaing wall. I then replace the remaining two screws. JOB DONE

Over a period of weeks I watched my fridge grand to a halt. It was...saddening. I felt helpless, there was nothing I could do and I wasn't prepared to pull in a repairman. Upon it's departure from being affective (broke) I made up my mind to purchase a new one!! Flash-forward five minutes n the internet ...motivator by high costs, I altered my thinking and visited You Tube for a fix-it video. After a quick search I came across a clip that took me to the heart of the problem. It was THAT easy. Wow!! I followed the instructions and quickly learned the failure had to do with a small, light weight fan that's role was to pull heat from the condenser--it had ceased to work. While waiting for the part, I let a small fan blow on the condenser to dissipate the heat. The fridge roared to life!! Like a charm!! When the new fan body arrived I placed the blade from the old fan on it and installed it (the fan did not come with bolts and the holes were not threaded) using sheet metal screws. It immediately came started performing again and has been doing a superb job ever since. I easily saved $800 in costs going this route!!

I just followed the enclosed instructions

Went online and found troubleshooting steps for this particular make, model, issue and ordered the parts recommended. Unplugged the refrigerator and removed the screws from the back panel and located the parts easily by using the instructions with pictures provided with the parts. The parts simply popped out without tools and popped back into place. Replaced the back panel and plugged in the refrigerator. Works like new.

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

Ordered part over the phone and received it two days later.....excellent service

Door cams were worn out. Removed food from door. Removed top hinge cover and hinge. Lifted door off lower hinge pin and placed door on a table. Removed old door cam and installed new one. Replaced closing cam on lower hinge. Set door back on lower hinge and closed door (magnetic strips hold the door in place). Reinstalled top hinge and replaced cover.

One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.

I cracked the crisper pan after having the refrigerator only one week and needed a replacement ASAP!! I was so happy to find this site and the part I needed. It's a little pricy for a plastic drawer but I can overlook that since it was in stock and I received it the very next day!!!I took out the cracked pan, slid in the new one and I was done!!!! No more unsightly crack!

My humidity control and veggie drawers were cracked and broken, I had shopped around but the price to replace them was too high and not in my budget. I came up on partselect.com while searching to find a more reasonable price. The price, service, delivery and customer service was outstanding. One of the drawer had been damaged during shipping, I called them and they sent another one free of charge right away. I had a very positive experience and I have added them to my favorite web sites.

I spoke with a friend of mine who does refrigeration and he suggested that I check the starter. I pulled it out and read your site to confirm the problem. The starter had loose particles just as your site mentioned. I ordered the part on Wed. afternoon and received it the next morning. When it came I received two different pieces which allowed for a product upgrade if needed. It wasn't and after I put it in it worked great. Freezer to -20 degrees F. Thanks...JT from Lucas, Ohio.

Order at 2:30 PM on Tuesday and had it by 1:30PM Wednesday. Less than a day on the delivery order. Thanks!